Pro Plumbers

When something goes wrong with your plumbing system, speed is essential. The faster you address the problem, the better off you and your wallet will be. Water can quickly cause thousands of dollars in damage. Leaks can soak floors, ceilings and foundations, causing rot and mold that may make your home uninhabitable. Get a direct quote from a professional plumber.  Continue Reading
The projects we've laid out here are particularly simple, but plumbing can be tricky, so if you're ever unsure, don't be afraid to ask for help. These projects are all pretty straightforward, but you never know what will come up, especially with older homes. We've selected some pretty good videos, but do some research and find some other videos if something about your setup looks a little different. The Internet is a wonderful thing.
Most typical single family home systems won't require supply piping larger than 3⁄4 inch (19 mm) due to expense as well as steel piping's tendency to become obstructed from internal rusting and mineral deposits forming on the inside of the pipe over time once the internal galvanizing zinc coating has degraded. In potable water distribution service, galvanized steel pipe has a service life of about 30 to 50 years, although it is not uncommon for it to be less in geographic areas with corrosive water contaminants.

Before you get involved with most plumbing projects, you'll need to shut off the water flowing to whatever you're working on. Most of the time, there are easy-to-access gate valves or compression valves that you can turn with your hand. Turn them clockwise all the way to turn off the water and counter-clockwise to turn it back on when you're done. For sinks, look under the sink and you'll usually see two valves—one for hot water and one for cold. On kitchen sinks, you might also see valves for the ice maker on your fridge or your dishwasher. Just turn them all off. For toilets, the valves are on the wall or right on the pipe behind the toilet.
Most plumbers, pipefitters, and steamfitters learn their trade through a 4- or 5-year apprenticeship. Apprentices typically receive 2,000 hours of paid on-the-job training, as well as some classroom instruction, each year. In the classroom, apprentices learn safety, local plumbing codes and regulations, and blueprint reading. They also study mathematics, applied physics, and chemistry. Apprenticeship programs are offered by unions and businesses. Although most workers enter apprenticeships directly, some start out as helpers. The Home Builders Institute offers a pre-apprenticeship training program in plumbing and other trades.
Most plumbers, pipefitters, and steamfitters learn their trade through a 4- or 5-year apprenticeship. Apprentices typically receive 2,000 hours of paid on-the-job training, as well as some classroom instruction, each year. In the classroom, apprentices learn safety, local plumbing codes and regulations, and blueprint reading. They also study mathematics, applied physics, and chemistry. Apprenticeship programs are offered by unions and businesses. Although most workers enter apprenticeships directly, some start out as helpers. The Home Builders Institute offers a pre-apprenticeship training program in plumbing and other trades.

I just had my pipe under the sink unclogged  and new pipes put in $600.00, then they flushed out the pipe from under the sink to the outside pipe $700.00, Total of $1.600.00, I thought that the price was high, I got the plumber from Home Advisors, not sure they had to do all they did but they said I needed the work done.  The same evening hike using the dishwasher I had a leak in one of the pipes they put in, they came back the next day to fix it. Don't know if I will use them again.. They were K&D kitchens.

I used Go Green Express Home Services for a minor plastic pipe repair under my kitchen sink...The worker did a great job fixing this minor pipe plastic pipe repair( my original pipe was too short and he needed to extended the pipe and then reconnect). It took him less than 10 minutes to fix. I was first quoted $125 +tax but when the worker went to his truck and spoke to whoever he spoke to at the office, the price rose to $155.10 +tax for a total of $167.10...I thought that was a little too high. Will I use this company again, I Don't Know. It would be helpful if they would have a set price list for jobs (minor repairs, Major repairs etc...), then you as the consumer can see beforehand what the cost maybe and work from there with the company. Minor repairs, Major repairs this company should at least have a set-price list. ..The worker was great and efficient and did a good job on the repair but their prices are a bit costly. And yes, I did write this in their review.

Using corrosive chemicals to dissolve a clog is like throwing a grenade down a gopher hole. Instead, Wroblewski recommends flushing your drains weekly with a half cup of baking soda and one cup of vinegar. Let it fizz in the drain for ten minutes, then pour in four cups of boiling water. Find out about the plumbing nightmares that will make you cringe.
Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.[19]
Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.
I just had my pipe under the sink unclogged  and new pipes put in $600.00, then they flushed out the pipe from under the sink to the outside pipe $700.00, Total of $1.600.00, I thought that the price was high, I got the plumber from Home Advisors, not sure they had to do all they did but they said I needed the work done.  The same evening hike using the dishwasher I had a leak in one of the pipes they put in, they came back the next day to fix it. Don't know if I will use them again.. They were K&D kitchens.
Most large cities today pipe solid wastes to sewage treatment plants in order to separate and partially purify the water, before emptying into streams or other bodies of water. For potable water use, galvanized iron piping was commonplace in the United States from the late 1800s until around 1960. After that period, copper piping took over, first soft copper with flared fittings, then with rigid copper tubing utilizing soldered fittings.
×