Baker Brothers Plumbing offers both residential and commercial plumbing services including tank and tankless water heater replacement and maintenance; drain and sewer repairs or replacement; drain cleaning, clearing and jetting; pipe lining and pipe replacement; repipe; gas line repair; slab leak detection and slab leak repair; bathroom and kitchen faucet installation; garbage disposal repair and installation; and most general plumbing repairs in most or all of the following Dallas, TX ZIP Codes: 75229, 75230, 75225, 75220, 75209, 75219, 75247, 75212, 75235, 75201, 75207, 75248, 75287, 75252, 75244, 75254, 75240, 75251, 75248-1713, 75214, 75228, 75243, 75238, 75218, 75206, 75231, 75204, 75226, 75246, 75227, 75208, 75217, 75232, 75224, 75211, 75241, 75215, 75233, 75253, 75216, 75223, 75237, 75249, 75203, 75210
Although needing emergency service for anything is never fun, if its plumbing service you ned I’d recommend Ben Franklin. The customer service person that took my call was courteous and professional. The service technician arrived well within the appointment time window. He was also courteous and professional. He understood my issue and explained what service was needed and what it would cost. He fixed the problem, cleaned up any debris that occurred during his work. We did the paperwork, he asked if I had any questions and then gave me his contact information in case I needed to call. You can’t beat that! Thanks!
I had called Ben Franklin to fix a pin hole leak in the meter horn. Booking an appointment was very easy and the crew (Sid and Brandon) showed up on time. They quickly found out that a stop valve was not working and had to be replaced as well. Sid clearly explained my options and the charges upfront. He dealt with the city for water shut off, went about the job in a quick and efficient manner. Sid was very professional and explained clearly what he was doing. He patiently answered all my questions. Brandon was very practical and frank. As they were finishing up (I had to leave the house for an hour) they spotted a leak in another valve and fixed that also. I thought it was highly ethical of them to do so. Thank you Sid and Brandon!
Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.
We strive in delivering top quality service to all of our customers. We want you happy and satisfied by the time we walk out your door. We will help locate your issue with a free estimate. Explain what the problem is and offer you our service to fix the problem. You are not obligated to use us. We treat each customer friendly, professional and courtesy.
Leaky faucets are more than just a minor inconvenience. All that dripping water can corrode your sink and drain basins, wear away at your pipes and waste hundreds of gallons per year! Don’t let this happen to you – call our friendly Baltimore, Washington D.C., Northern Virginia, Delaware and the Philadelphia plumbing technicians for faucet repair today!
Estimating a plumbing job is best left to the professionals. However, our guides linked to throughout this article are the best first step to understanding pricing. Understanding basic plumbing is an excellent second step. Not only does this help you diagnose potential problems before they become costly ones, but itll help you understand what a plumber does.
The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.
Most plumbers, pipefitters, and steamfitters learn their trade through a 4- or 5-year apprenticeship. Apprentices typically receive 2,000 hours of paid on-the-job training, as well as some classroom instruction, each year. In the classroom, apprentices learn safety, local plumbing codes and regulations, and blueprint reading. They also study mathematics, applied physics, and chemistry. Apprenticeship programs are offered by unions and businesses. Although most workers enter apprenticeships directly, some start out as helpers. The Home Builders Institute offers a pre-apprenticeship training program in plumbing and other trades.
toilets work off of siphon.more correctly it's the timely transfer of water from the tank to the bowl through the ports that starts the siphon and carrys the solids and water downstream,thus completing a flush.i also live in florida and due to lots of hard water everywhere can tell you that most likely the toilets are full of deposits and need to be replaced or are of poor quality.all of the toilets from home depot are trash i would suggest getting one from the factory or from a plumbing supply house.DO NOT GET A 1.28gpf...1.6gpf is still legal