My parents are in their middle eightys and my mother is at home with cancer. They live in SaintAugustine Florida.My problem is their two toilets will not flush all the way down the drain. I. have been down there twice to help them but I cannot drive 1200 miles each time they have a problem.So for now I would like to know what I can translate to my father over the phone to remedy this situation. Thank you very much Ray Dupuis.
Galvanized steel potable water supply and distribution pipes are commonly found with nominal pipe sizes from 3⁄8 inch (9.5 mm) to 2 inches (51 mm). It is rarely used today for new construction residential plumbing. Steel pipe has National Pipe Thread (NPT) standard tapered male threads, which connect with female tapered threads on elbows, tees, couplers, valves, and other fittings. Galvanized steel (often known simply as "galv" or "iron" in the plumbing trade) is relatively expensive, and difficult to work with due to weight and requirement of a pipe threader. It remains in common use for repair of existing "galv" systems and to satisfy building code non-combustibility requirements typically found in hotels, apartment buildings and other commercial applications. It is also extremely durable and resistant to mechanical abuse. Black lacquered steel pipe is the most widely used pipe material for fire sprinklers and natural gas.
Clogged drains are no fun. We've shown you several ways to clear a clogged drain and how to clear a blocked P-trap under a sink, but bathtub drains can be a little more challenging. A lot more hair and other gunk goes down them than you think. Add to this the fact that most bathtub drains take a 90-degree turn that makes getting a drain snake down them more difficult.
Don’t try to repair, replace, or install faulty or broken plumbing equipment on your own. Hire the top plumbers in town to take care of your needs! We’re capable of detecting the source of the issues fast. Trust us to advise you on the most effective solutions custom-tailored to eliminating them. Our Cincinnati plumbing company always comes prepared with the best tools and equipment. We also provide upfront pricing and money-saving deals and specials to keep more money in your pockets.
Hello! My name is Lorinn and I am 26 years old. I have been working in different construction trades for 8+ years now. To name a few I am a skilled in flooring, cabinets/closets, and electrical(fans, fixtures, etc). I’ve gotten as experienced as I am because I genuinely enjoy working with my hands and learning new things. I take pride in my work, and love exceeding peoples expectations.
If nothing inside the home was altered you should not be getting a smell. Personally I'm confused as to why the repair person would have left the original line there and ran another one through a new hole. I would have pulled the old line up, ran the new line (in PVC) and used the same hole in the septic tank instead of creating a new one. Did he seal up the hole in the tank from the old line?
To unclog a bathtub drain the right way, you'll need to take the drain plate off. That's the little round plate that has the lever on it for opening and closing the pop-up drain stopper. It takes a little effort, but it's not too hard to remove and behind that plate, you have access to a straight drain pipe you can send the drain snake down. Check out the video above from This Old House for instructions.
Hello I had a plumber do an estimate for me to replace our copper pipes with plastic as we have no existing walls up in our basement yet...pretty basic job... so we figured we could upgrade as we do live in Northern Ontario and it does tend to get quite cold here in the winters. We dont have any existing problems with our plumbing right now just figured it would be good time to do the job and perhaps change the pipes to 3 quarter inch for faster flow. Well I never thought in all my life I would get an estimate back that would state $350.00 an hour in labor...yes that is correct $350.00 an hour...estimated 10 hours for the job to be completed. So he quoted me $3500.00 for labor alone.. not supplies? Well needless to say I will be happy with my half inch copper pipes and will happily wait for my bathtub to fill up at a slower pace. Just wanted to know what your thoughts are on this $350.00 an hour quote? Thank you and enjoy your day.
Plumbers on the Handy platform have experience in fixing all the common (and uncommon) plumbing problems that plague homes. Whether you’ve got a water heater leaking, a clogged toilet, or a blocked drain, chances are that your plumber will have seen and dealt with a similar job before. When you use the Handy app or website, you’ll be connected to experienced plumbers who’ll know exactly what to do, no matter how big or small the job might be.
Cast iron and ductile iron pipe was long a lower-cost alternative to copper, before the advent of durable plastic materials but special non-conductive fittings must be used where transitions are to be made to other metallic pipes, except for terminal fittings, in order to avoid corrosion owing to electrochemical reactions between dissimilar metals (see galvanic cell).