Pro Plumbers

Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.
We are members of St. Gertrude's Parish and we experienced a sewer back up in our basement. I saw BEST Plumbing listed in the bulletin and I decided to give you a try. The appointment was made between 2:00pm and 4:00pm. I received a call from our plumber at approximately 1:30pm that he was in route to our house. BEST Plumbing cleared roots out of our sewer line and operated a camera in the sewer line. They discovered a riser installed improperly, which was broken at the lateral connection. BEST Plumbing made proper repairs, placed sand and backfilled the area. Our plumber was extremely courteous, helpful, and very professional throughout the entire process. We will be BEST Plumbing's biggest fans and appreciate the service. St. Gertrude's Parish
Sometimes a faucet leak can be stopped by replacing the rubber washer at the end of a faucet stem or cartridge.  This is a more common repair on older fixtures when things were built to last and designed to be able to be maintained.  Other times the whole stem or cartridge needs replacement or the bibb seat deeper back into the fixture needs replacement.  That leads to matching up the right components and often times making a trip to the hardware store or plumbing supply house necessary due to the many varieties, makes and models of faucets.  My advice is to make sure your Plumber has faucet repair kit on their truck before having them come out to assess the issue.
To unclog a bathtub drain the right way, you'll need to take the drain plate off. That's the little round plate that has the lever on it for opening and closing the pop-up drain stopper. It takes a little effort, but it's not too hard to remove and behind that plate, you have access to a straight drain pipe you can send the drain snake down. Check out the video above from This Old House for instructions.
I had 207 Plumbing come to fix a leak in my ceiling.  It's a terrible, terrible company to do business with.  He came and fixed a broken pipe in the ceiling, and I asked him to check the rest of the pipe to make sure that nothing else was broken, he said everything was OK and charged me $219.00 for 45 minutes and left.  Never cleaned up his mess.  I went to clean up the mess after he left and found there was more damage to the pipe.  I called him to come back, which he did.  He looked at the water coming down from the ceiling, into a light fixture and said he had another job to go to and couldn't come back until next week.  He also wanted to charge me $350.00 to come back.  I told him that was too much and he said he would make an exception and only charge me $219.00.  Now I have major damage done to the ceiling, the light fixture and the floor.  All of this could have been prevented if he had stayed and fixed the problem.  I will NOT hire him again.
When you need plumbing or HVAC services in Castle Rock, there’s only one choice to make: PRO Plumbing Service. With more than 2500 service calls per year, we are your trusted plumbing, heating, and air conditioning company. If you are looking for a family-owned and operated plumbing and HVAC company, our top-rated HVAC contractors and plumbers ready to assist.

Two-handle faucets are most often found in the bathroom, but you see them in some kitchens. Two-handle faucets use three types of mechanisms. The first two are the same as two of the mechanisms used in a single-handle faucet: cartridge and ceramic disc. The third type is a compression (or reverse-compression) mechanism. Compression faucets are the simplest type, using rubber washers that get compressed against one another to seal the valve. They do tend to wear out faster than other faucet types, but are also least expensive to repair.


Welcome to Atlanta Plumber Repair, offering you with plumbing services in the Atlanta area and surrounding areas as well. If you are looking for residential plumbing services along with reliable commercial plumbing services, the one company in Atlanta that will be able to assist you is the one company that can offer you all this for a great and affordable price, Atlanta Plumber Repair. All of our plumbers that are with us, are either trained and fully licensed or backed with our over 25 years of plumbing experience to get you the right type of plumbing treatment for your home that you are looking for.
Also, you might run into a problem where the shower arm is too short or angled too sharply for the shower head you bought. This can happen more with the wand-type shower heads and the wall gets in the way of the wand. You can solve this problem by making sure you buy a shower head that fits or installing an extension arm onto the main shower arm. You can find those the same place you buy the shower heads.
In the United Kingdom the professional body is the Chartered Institute of Plumbing and Heating Engineering (educational charity status) and it is true that the trade still remains virtually ungoverned;[36] there are no systems in place to monitor or control the activities of unqualified plumbers or those home owners who choose to undertake installation and maintenance works themselves, despite the health and safety issues which arise from such works when they are undertaken incorrectly; see Health Aspects of Plumbing (HAP) published jointly by the World Health Organization (WHO) and the World Plumbing Council (WPC).[37][38] WPC has subsequently appointed a representative to the World Health Organization to take forward various projects related to Health Aspects of Plumbing.[39]
Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.
We partner with a third party ad network to either display advertising on our Web site or to manage our advertising on other sites. Our ad network partner uses cookies and Web beacons to collect non-personally identifiable information about your activities on this and other Web sites to provide you targeted advertising based upon your interests. If you wish to not have this information used for the purpose of serving you targeted ads, you may opt-out by clicking here. Please note this does not opt you out of being served advertising. You will continue to receive generic ads.
Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.[19]
×