Pro Plumbers

Clogged drains are no fun. We've shown you several ways to clear a clogged drain and how to clear a blocked P-trap under a sink, but bathtub drains can be a little more challenging. A lot more hair and other gunk goes down them than you think. Add to this the fact that most bathtub drains take a 90-degree turn that makes getting a drain snake down them more difficult.


I had 207 Plumbing come to fix a leak in my ceiling.  It's a terrible, terrible company to do business with.  He came and fixed a broken pipe in the ceiling, and I asked him to check the rest of the pipe to make sure that nothing else was broken, he said everything was OK and charged me $219.00 for 45 minutes and left.  Never cleaned up his mess.  I went to clean up the mess after he left and found there was more damage to the pipe.  I called him to come back, which he did.  He looked at the water coming down from the ceiling, into a light fixture and said he had another job to go to and couldn't come back until next week.  He also wanted to charge me $350.00 to come back.  I told him that was too much and he said he would make an exception and only charge me $219.00.  Now I have major damage done to the ceiling, the light fixture and the floor.  All of this could have been prevented if he had stayed and fixed the problem.  I will NOT hire him again.
 CON'T FROM COMMENTS EARLIER.  However,  the  installation took less than 3/4/ hour and was a basic regulator with no other function.  Looking up the price afterwards, invoice did not list type or price, it appears that it would have cost me around $60 for the regulator and another $15 or so for the additional supplies necessary to install it and it was really a rather simple job with easy access.    Given that, it seems that $300 for less that  an hours worth of on site work,  company says it does not include commute time in its prices, is a little high.  While flat rate quotes are nice, they must take into consideration situations where the work load differs depending on the circumstances.  Therefore, unless you are at the upper end of the harder work needed than the average job. it can be argued that my estimated price of $300 for labor was more than a little high.  Maybe I am wrong since I have not used their services for years and  am not knowledgeable of the costs of equipment and professional labor today.  
The Delta 5 in. Hand shower Diverter Spout The Delta 5 in. Hand shower Diverter Spout in Chrome is a key component to a coordinated and multi-functional bath. As part of a company that delivers water every day through millions of faucets worldwide Delta provides a lifetime limited warranty on all parts to the original consumer. Delta is ...  More + Product Details Close
Before you get involved with most plumbing projects, you'll need to shut off the water flowing to whatever you're working on. Most of the time, there are easy-to-access gate valves or compression valves that you can turn with your hand. Turn them clockwise all the way to turn off the water and counter-clockwise to turn it back on when you're done. For sinks, look under the sink and you'll usually see two valves—one for hot water and one for cold. On kitchen sinks, you might also see valves for the ice maker on your fridge or your dishwasher. Just turn them all off. For toilets, the valves are on the wall or right on the pipe behind the toilet.
Bacteria have been shown to live in "premises plumbing systems". The latter refers to the "pipes and fixtures within a building that transport water to taps after it is delivered by the utility".[34] Community water systems have been known for centuries to spread waterborne diseases like typhoid and cholera, however "opportunistic premises plumbing pathogens" have been recognized only more recently; Legionella pneumophila discovered in 1976, Mycobacterium avium, and Pseudomonas aeruginosa are the most commonly tracked bacteria, which people with depressed immunity can inhale or ingest and may become infected with.[35] These opportunistic pathogens can grow for example in faucets, shower heads, water heaters and along pipe walls. Reasons that favor their growth are "high surface-to-volume ratio, intermittent stagnation, low disinfectant residual, and warming cycles". A high surface-to-volume ratio, i.e. a relatively large surface area allows the bacteria to form a biofilm, which protects them from disinfection.[35]
PVC/CPVC – rigid plastic pipes similar to PVC drain pipes but with thicker walls to deal with municipal water pressure, introduced around 1970. PVC stands for polyvinyl chloride, and it has become a common replacement for metal piping. PVC should be used only for cold water, or for venting. CPVC can be used for hot and cold potable water supply. Connections are made with primers and solvent cements as required by code.[22]
Water systems of ancient times relied on gravity for the supply of water, using pipes or channels usually made of clay, lead, bamboo, wood, or stone. Hollowed wooden logs wrapped in steel banding were used for plumbing pipes, particularly water mains. Logs were used for water distribution in England close to 500 years ago. US cities began using hollowed logs in the late 1700s through the 1800s. Today, most plumbing supply pipe is made out of steel, copper, and plastic; most waste (also known as "soil")[21] out of steel, copper, plastic, and cast iron.[21]
I just had my pipe under the sink unclogged  and new pipes put in $600.00, then they flushed out the pipe from under the sink to the outside pipe $700.00, Total of $1.600.00, I thought that the price was high, I got the plumber from Home Advisors, not sure they had to do all they did but they said I needed the work done.  The same evening hike using the dishwasher I had a leak in one of the pipes they put in, they came back the next day to fix it. Don't know if I will use them again.. They were K&D kitchens.
Occupational employment projections are developed for all states by Labor Market Information (LMI) or individual state Employment Projections offices. All state projections data are available at www.projectionscentral.com. Information on this site allows projected employment growth for an occupation to be compared among states or to be compared within one state. In addition, states may produce projections for areas; there are links to each state’s websites where these data may be retrieved.
I thought that my sump pump had ended its life and needed to be replaced. The contractor I found through Home Adviser came out the following day and arrived reasonably promptly.  The technician tested the pump and it wasn't responding. He then checked the  breaker panel and all seemed well. However he checked to see if power was reaching the outlet, it wasn't so he tripped some breakers and reset them and the power to my pump came on and the pump works so a replacement wasn't necessary. He charged $75.00 which I think was reasonable for a call-out fee and time spent.
As with other construction workers, employment of plumbers, pipefitters, and steamfitters is sensitive to fluctuations in the economy. On the one hand, workers may experience periods of unemployment when the overall level of construction falls. On the other hand, shortages of workers may occur in some areas during peak periods of building activity.
Most states and localities require plumbers to be licensed. Although licensing requirements vary, most states and localities require workers to have 2 to 5 years of experience and to pass an exam that shows their knowledge of the trade and of local plumbing codes before they are permitted to work independently. In addition, most employers require plumbers to have a driver’s license.
PVC/CPVC – rigid plastic pipes similar to PVC drain pipes but with thicker walls to deal with municipal water pressure, introduced around 1970. PVC stands for polyvinyl chloride, and it has become a common replacement for metal piping. PVC should be used only for cold water, or for venting. CPVC can be used for hot and cold potable water supply. Connections are made with primers and solvent cements as required by code.[22]
Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.
Plumbers, pipefitters, and steamfitters may use many different materials and construction techniques, depending on the type of project. Residential water systems, for example, use copper, steel, and plastic pipe that one or two plumbers can install. Power plant water systems, by contrast, are made of large steel pipes that usually take a crew of pipefitters to install. Some workers install stainless steel pipes on dairy farms and in factories, mainly to prevent contamination.
We partner with a third party ad network to either display advertising on our Web site or to manage our advertising on other sites. Our ad network partner uses cookies and Web beacons to collect non-personally identifiable information about your activities on this and other Web sites to provide you targeted advertising based upon your interests. If you wish to not have this information used for the purpose of serving you targeted ads, you may opt-out by clicking here. Please note this does not opt you out of being served advertising. You will continue to receive generic ads.

As with other construction workers, employment of plumbers, pipefitters, and steamfitters is sensitive to fluctuations in the economy. On the one hand, workers may experience periods of unemployment when the overall level of construction falls. On the other hand, shortages of workers may occur in some areas during peak periods of building activity.
At Steve’s Plumbing Service, our Oahu plumbers are highly skilled at customizing your plumbing system to you and your family’s unique needs. Whenever you are remodeling your home, you have a great opportunity to improve the comfort that your home provides and the uses to which you can put your home. Our plumbing professionals can install plumbing fixtures and appliances that will enhance both of these aspects. Maximize the benefits of your next remodeling project by hiring our highly skilled professionals.
Needed to replace a water pressure regulator.  Looking at the retail costs of the regulator, they seem to run from abouit $60 to over $300 for one that includes more that the basic control of water pressure in the house.  Had not used a pro plumber for over 20 years so I was not up on the costs associated with needing their help.  I was contacted by at least 3 plumbers but only one, Right Now Plumbers, gave me an instant quote of $394  for the service without me even asking. Although I thought this price seemed a little high for a job that takes less than an hour to complete, I accepted their service.  Must say that the job was done very professionally and would use them again if needed.  However,
Many commercial properties face the same plumbing problems as residential buildings. Usually, the plumbing system is much larger and more complex. The effects of plumbing problems can be much more extensive for commercial buildings, as they can interrupt business and impact profits. So it’s critical that you have a plumbing company you can trust when problems strike to minimize disruption to your operations.

For details about apprenticeship or other opportunities in this occupation, contact the offices of the state employment service; the state apprenticeship agency; local plumbing, heating, and cooling contractors or firms that employ fitters; or local union–management apprenticeship committees. Apprenticeship information is available from the U.S. Department of Labor's Apprenticeship program online, or by phone at 877-872-5627.
B&L Plumbing Service, Inc. offers a variety of residential and commercial plumbing services in the Kansas City metro area. We are a family owned and operated business and have been satisfying our customers since 1998. At B&L Plumbing, we go above and beyond to take care of our customers and are always ready to take care of any problem that you may have with your plumbing systems. We know your time is valuable. That is why when you call, we will arrive when you need us with a skilled service technician and a well stocked truck ready to troubleshoot, and repair your plumbing problem on the spot.
Even the smallest issues with your heating or air conditioning can quickly become an emergency. If your furnace is failing to produce heat, or your air conditioner is blowing hot air, call the air conditioning and heating repair company that you can trust. With emergency service available 24/7 by our trusted technicians, keeping reliable cooling and heating is easy all year long.
If you have a leaking faucet in your home, it could be costing you hundreds of dollars a year on your water bills. A faulty tap can also lead to the growth of unhealthy mold and mildew. One of our expert technicians can quickly and efficiently take care of repairing or replacing that leaking faucet. We can also take care of installing or repairing any of the other plumbing fixtures in your home, including sinks toilets and showers.
Also, you might run into a problem where the shower arm is too short or angled too sharply for the shower head you bought. This can happen more with the wand-type shower heads and the wall gets in the way of the wand. You can solve this problem by making sure you buy a shower head that fits or installing an extension arm onto the main shower arm. You can find those the same place you buy the shower heads.
Before you get involved with most plumbing projects, you'll need to shut off the water flowing to whatever you're working on. Most of the time, there are easy-to-access gate valves or compression valves that you can turn with your hand. Turn them clockwise all the way to turn off the water and counter-clockwise to turn it back on when you're done. For sinks, look under the sink and you'll usually see two valves—one for hot water and one for cold. On kitchen sinks, you might also see valves for the ice maker on your fridge or your dishwasher. Just turn them all off. For toilets, the valves are on the wall or right on the pipe behind the toilet.
plumbers must be asked directly what they charge hourly and if that is in addition to a service charge. The two are separate and I think they have gotten away with outrageous charges because of the potential of water damaging homeowner structures.   I had a plumber (not Home advisor) come and replace a part in my kitchen sink that was under warranty---the spray nozzle had been leaking...He charged me $85.00 for 15 minutes of work and I will never use Mr King again. 

Plumbers in Australia have licensing requirements that differ from state to state but it is generally accepted a 4-year apprenticeship with a further minimum experience of 2 years (6 years total) and a further curricular requirement as a benchmark for licensing. Licensed plumbers are also expected to maintain minimum relevant training requirements to maintain their plumbing license
×