Pro Plumbers

Our sewer repair and replacement experts service Baltimore, Washington D.C., Northern Virginia, Delaware and the Philadelphia Area.  The specific counties we service are:  Baltimore County, Howard County, Montgomery County, Prince Georges County, Anne Arundel County, Harford County, Carroll County, Fairfax, New Castle County, Delaware County, Chester County, Stafford County, Fredericksburg County, Fairfax City, Alexandria, Arlington County, Loudon County, Prince William County, Falls Church, Manassas and Cecil County.
It’s a family event in late October when many American households carve a pumpkin into a Halloween jack-o-lantern. The kids delight in the whole process, especially when mom and dad let junior scoop the pumpkin pulp out of the pumpkin. But what happens next is the scary part. Often, those slimy pumpkin guts are pushed down the sink drain then the disposal is turned on to chop it into tiny bits before the water washes it away. Except, it doesn’t quite ... Read More >

Pipefitters, sometimes simply called fitters, install and maintain pipes that carry chemicals, acids, and gases. These pipes are used mostly in manufacturing, commercial, and industrial settings. Fitters install and repair pipe systems in power plants, as well as heating and cooling systems in large office buildings. Some pipefitters specialize as gasfitters, sprinklerfitters, or steamfitters.
If your bathroom sink is slowly draining instead of holding water, your problem is super easy to fix. You likely just need to make a quick adjustment to the assembly under the sink. Pop-up drains have an arm that reaches down the drain and connects to a little rod. That rod sticks through the drain pipe and is held in place by a metal strip with holes in it. That strip, in turn, is connected to the little lever or handle you pull on to open and close the stopper. The video above from HomeAdditionPlus has an excellent look at how to make adjustments.
Using corrosive chemicals to dissolve a clog is like throwing a grenade down a gopher hole. Instead, Wroblewski recommends flushing your drains weekly with a half cup of baking soda and one cup of vinegar. Let it fizz in the drain for ten minutes, then pour in four cups of boiling water. Find out about the plumbing nightmares that will make you cringe.
Water systems of ancient times relied on gravity for the supply of water, using pipes or channels usually made of clay, lead, bamboo, wood, or stone. Hollowed wooden logs wrapped in steel banding were used for plumbing pipes, particularly water mains. Logs were used for water distribution in England close to 500 years ago. US cities began using hollowed logs in the late 1700s through the 1800s. Today, most plumbing supply pipe is made out of steel, copper, and plastic; most waste (also known as "soil")[21] out of steel, copper, plastic, and cast iron.[21]
Having the right tools can mean the difference between a quick project and a complete mess. Fortunately, you won't need too much to handle the projects here and what you will need is pretty inexpensive (certainly less expensive than hiring a plumber). You can get everything on this list for about $100, and you won't need it all unless you're doing all the projects. Where I live, that's about the cost of hiring a plumber for an hour.
For over 24 years, PRO Plumbing Services has been a local, trusted family plumber, serving all of Douglas County and the surrounding areas including Castle Rock, Franktown, Elizabeth, Highland's Ranch, Sedalia, South Metro Denver, Front Range, and Parker. All of our employees are background checked and drug tested to ensure only trustworthy technicians are entering your home or business.
Curtis did an excellent job in identifying the problem and providing a couple solutions. We discussed both and came to a mutual agreement, rather than him explicitly saying this is the only option and charge excessive amount. Curtis was very easy to talk to; even though I had lots of questions he was very professional throughout. He was prompt to the appointment, although I forgot about the time, he reached out and waited until I arrive. I would highly recommend their services for your plumbing needs!
With experience and expertise, your plumber will be able to inspect your plumbing fixtures and identify where any problems may have originated. With the right tools on hand, they’ll be able to fix the problem, right there and then. If your water heater has  triggered a full-blown flood, they’ll know exactly how and where to shut off the water supply. Should the flood be the result of a burst pipe, they’ll be able to change it before it can do any additional damage. Plumbers know a lot about their craft that we do not, and the Handy platform gives you the opportunity to book them and benefit from their knowledge and ability.
The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.
Leaky faucets are more than just a minor inconvenience. All that dripping water can corrode your sink and drain basins, wear away at your pipes and waste hundreds of gallons per year! Don’t let this happen to you – call our friendly Baltimore, Washington D.C., Northern Virginia, Delaware and the Philadelphia plumbing technicians for faucet repair today!
There are few things worse than waiting for a plumber after being given an 8 hour time window, while your sink is spouting water all over the carpet or your toilet is overflowing. Using the Handy platform, you can arrange an exact time for your plumber to arrive, which means you don’t have to take an entire day off of work to sit around and wait for them. The plumbers on the Handy platform have seen it all and they have the ratings and reviews to prove it.  We’ll match the details of your job with a reliable plumber in your area before you know it.
Before starting any work, we study the issue and perform comprehensive inspections to properly diagnose the problem. Once we have pinpointed the source of the issue, we will discuss your options with you. We try to stick to repairs if possible, and avoid recommending replacements unless your system or unit is extremely outdated. By focusing on repairs instead of replacement, you save money and enjoy an improved plumbing unit for many more years to come.
Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.
At Len The Plumber, we’ve seen it all when it comes to leaky faucets. Let’s face it – your faucets are some of the most frequently used appliances in your home. All that wear and tear is bound to catch up with them at some point! That’s why we offer fast, full-service faucet repair and replacement in the Baltimore, Washington D.C., Northern Virginia, Delaware and the Philadelphia area seven days a week. Call us today if you need:
Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.[19]
×