Pro Plumbers

Clogged drains are no fun. We've shown you several ways to clear a clogged drain and how to clear a blocked P-trap under a sink, but bathtub drains can be a little more challenging. A lot more hair and other gunk goes down them than you think. Add to this the fact that most bathtub drains take a 90-degree turn that makes getting a drain snake down them more difficult.
Needed to replace a water pressure regulator.  Looking at the retail costs of the regulator, they seem to run from abouit $60 to over $300 for one that includes more that the basic control of water pressure in the house.  Had not used a pro plumber for over 20 years so I was not up on the costs associated with needing their help.  I was contacted by at least 3 plumbers but only one, Right Now Plumbers, gave me an instant quote of $394  for the service without me even asking. Although I thought this price seemed a little high for a job that takes less than an hour to complete, I accepted their service.  Must say that the job was done very professionally and would use them again if needed.  However,
Galvanized steel potable water supply and distribution pipes are commonly found with nominal pipe sizes from 3⁄8 inch (9.5 mm) to 2 inches (51 mm). It is rarely used today for new construction residential plumbing. Steel pipe has National Pipe Thread (NPT) standard tapered male threads, which connect with female tapered threads on elbows, tees, couplers, valves, and other fittings. Galvanized steel (often known simply as "galv" or "iron" in the plumbing trade) is relatively expensive, and difficult to work with due to weight and requirement of a pipe threader. It remains in common use for repair of existing "galv" systems and to satisfy building code non-combustibility requirements typically found in hotels, apartment buildings and other commercial applications. It is also extremely durable and resistant to mechanical abuse. Black lacquered steel pipe is the most widely used pipe material for fire sprinklers and natural gas.
Hi Kenneth, We would be happy to get you connected with a pro for your project. You can submit a service request on our website: http://www.homeadvisor.com/, or browse reviews for local water heater pros here: http://www.homeadvisor.com/c.html. We can also have a project advisor reach out to assist you if you send your contact information to [email protected] –HASupport
Stopping toilets from clogging is a function of keeping the toilet clear as well as keeping the pipes in the home clear. When the toilet is clogging often, it is best to make sure that the toilet is not being asked to flush a large number of solid products. Typically, the toilet should only be flushed with fluids. If the toilet is being overworked, it will clog. Also, the pipes in the house could begin to clog and force the toilet to clog at times when it appears that it should flush. It is best to contact annual professional cleaning services in order to keep your drains running smoothly.

Think that by calling for plumbing services you will have to clean up after the work is done? Not when you work with us! At Bud’s Plumbing & Repair Service, our uniformed plumbers arrive at your door with shoe covers and are conscious of the cleanliness of the work area. In fact, once the job is done, you won’t be able to tell we were even there! That’s how clean we leave your property. There is no mess for you to clean up, so you can get back to your normal routine without hassle.
Plumbers on the Handy platform have experience in fixing all the common (and uncommon) plumbing problems that plague homes. Whether you’ve got a water heater leaking, a clogged toilet, or a blocked drain, chances are that your plumber will have seen and dealt with a similar job before. When you use the Handy app or website, you’ll be connected to experienced plumbers who’ll know exactly what to do, no matter how big or small the job might be.
Most plumbers wont mess with the septic tank. We deal mostly with components inside the house. Did you have a vent pipe in the yard (often looks like a candy cane made of PVC) before the repair but not after? If all he did was replace the line it shouldn't cause a smell inside the house. All plumbing fixtures inside the house should have properly functioning traps. Those traps would create and maintain a water seal against the sewer gases. You should have at least one vent through the roof to equalize pressures within the drainage system. This prevents positive pressures within the system (caused by fixtures discharging into the lines, ie toilet flush) from pushing gas out through the traps, and negative pressures (the waste in line will pull air behind it like your finger over the end of a straw) from sucking water out of the traps.
Todd did an amazing job, and fixed a problem that could of been devastating. Replacing a leaking water heater and also a replacing a failing, leaking main shut of valve. The possibility of major flooding was a real danger It was a 12 unit townhome which made the job even trickier, as water had to be shut off to the entire building while he fixed the valve. Todd, replaced them quickly and expertly, without a hitch. Plumbing repairs are never fun for a homeowner, but these people (especially Todd) do great work. It is definitely a weight lifted off my chest.
If you have a leaking faucet in your home, it could be costing you hundreds of dollars a year on your water bills. A faulty tap can also lead to the growth of unhealthy mold and mildew. One of our expert technicians can quickly and efficiently take care of repairing or replacing that leaking faucet. We can also take care of installing or repairing any of the other plumbing fixtures in your home, including sinks toilets and showers.
I think it is rather rude and a bit dishonest for people to not divulge their total fees upfront, an of course we should know to ask. But the normal person wouldn't know the questions to ask until they are burnt once like this, and then there still could be costs for walking up stairs or charge another service call if they need to go somewhere to use the bathroom and come back. THAT ISN'T A QUESTION I WOULD THINK TO ASK.

Sometimes a faucet leak can be stopped by replacing the rubber washer at the end of a faucet stem or cartridge.  This is a more common repair on older fixtures when things were built to last and designed to be able to be maintained.  Other times the whole stem or cartridge needs replacement or the bibb seat deeper back into the fixture needs replacement.  That leads to matching up the right components and often times making a trip to the hardware store or plumbing supply house necessary due to the many varieties, makes and models of faucets.  My advice is to make sure your Plumber has faucet repair kit on their truck before having them come out to assess the issue.

The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.
Help! The toilet won’t stop running. It’s a bummer, sure, but it’s something you don’t need to call your plumber about. In fact, DIYers should take note that it’s a quick fix that will cost you just $5. For instance, your handle might just be sticking, which can be solved by spraying some lubricant where the handle meets the porcelain. Ready to DIY? Here’s how to fix a running toilet.
For many centuries, lead was the favoured material for water pipes, because its malleability made it practical to work into the desired shape. (Such use was so common that the word "plumbing" derives from plumbum, the Latin word for lead.) This was a source of lead-related health problems in the years before the health hazards of ingesting lead were fully understood; among these were stillbirths and high rates of infant mortality. Lead water pipes were still widely used in the early 20th century, and remain in many households. In addition, lead-tin alloy solder was commonly used to join copper pipes, but modern practice uses tin-antimony alloy solder instead, in order to eliminate lead hazards.[13]
×