Pro Plumbers

If your bathroom sink is slowly draining instead of holding water, your problem is super easy to fix. You likely just need to make a quick adjustment to the assembly under the sink. Pop-up drains have an arm that reaches down the drain and connects to a little rod. That rod sticks through the drain pipe and is held in place by a metal strip with holes in it. That strip, in turn, is connected to the little lever or handle you pull on to open and close the stopper. The video above from HomeAdditionPlus has an excellent look at how to make adjustments.
To unclog a bathtub drain the right way, you'll need to take the drain plate off. That's the little round plate that has the lever on it for opening and closing the pop-up drain stopper. It takes a little effort, but it's not too hard to remove and behind that plate, you have access to a straight drain pipe you can send the drain snake down. Check out the video above from This Old House for instructions.
Most typical single family home systems won't require supply piping larger than 3⁄4 inch (19 mm) due to expense as well as steel piping's tendency to become obstructed from internal rusting and mineral deposits forming on the inside of the pipe over time once the internal galvanizing zinc coating has degraded. In potable water distribution service, galvanized steel pipe has a service life of about 30 to 50 years, although it is not uncommon for it to be less in geographic areas with corrosive water contaminants.
Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.
Think that by calling for plumbing services you will have to clean up after the work is done? Not when you work with us! At Bud’s Plumbing & Repair Service, our uniformed plumbers arrive at your door with shoe covers and are conscious of the cleanliness of the work area. In fact, once the job is done, you won’t be able to tell we were even there! That’s how clean we leave your property. There is no mess for you to clean up, so you can get back to your normal routine without hassle.
Cast iron and ductile iron pipe was long a lower-cost alternative to copper, before the advent of durable plastic materials but special non-conductive fittings must be used where transitions are to be made to other metallic pipes, except for terminal fittings, in order to avoid corrosion owing to electrochemical reactions between dissimilar metals (see galvanic cell).[17]
We actually have our own guide on this, but the above video from Lowe's is a good basic guide too. Do make sure to read the installation instructions that come with the faucet, though. Sometimes, there are important variations. We've only included a video on kitchen sinks here because the process of installing a bathroom sink is largely the same. However, you can always check out this video from RONAinc if you want to see the process.
If nothing inside the home was altered you should not be getting a smell. Personally I'm confused as to why the repair person would have left the original line there and ran another one through a new hole. I would have pulled the old line up, ran the new line (in PVC) and used the same hole in the septic tank instead of creating a new one. Did he seal up the hole in the tank from the old line?
Before you get involved with most plumbing projects, you'll need to shut off the water flowing to whatever you're working on. Most of the time, there are easy-to-access gate valves or compression valves that you can turn with your hand. Turn them clockwise all the way to turn off the water and counter-clockwise to turn it back on when you're done. For sinks, look under the sink and you'll usually see two valves—one for hot water and one for cold. On kitchen sinks, you might also see valves for the ice maker on your fridge or your dishwasher. Just turn them all off. For toilets, the valves are on the wall or right on the pipe behind the toilet.
Help! The toilet won’t stop running. It’s a bummer, sure, but it’s something you don’t need to call your plumber about. In fact, DIYers should take note that it’s a quick fix that will cost you just $5. For instance, your handle might just be sticking, which can be solved by spraying some lubricant where the handle meets the porcelain. Ready to DIY? Here’s how to fix a running toilet.
Owning a home is an exciting adventure. Homeownership brings family, comfort, and memories. But along with the good times, you have to put up with the occasional interruptions. Plumbing problems are a natural part of life and a necessary evil. They will happen, and when they do, you should be prepared with a reliable solution. Texas Plumbing Repair is your go-to full-service plumbing company who specializes in home and business plumbing projects of every size and kind.
Jump up ^ "II. The Plumbers". The Atlantic. Retrieved 17 September 2013. In the early evening of June 17, 1971, Henry Kissinger held forth in the Oval Office, telling his President, and John Ehrlichman and Bob Haldeman, all about Daniel Ellsberg. Kissinger's comments were recorded, of course, on the hidden White House taping system, and four years later, a portion of that tape was listened to by the Watergate Special Prosecution Force, which was then investigating the internal White House police unit known as the Plumbers.
×