Pro Plumbers

Len The Plumber is a full service plumbing and drain cleaning company serving the entire Baltimore, Washington D.C., Northern Virginia, Delaware and the Philadelphia Area as well as Anne Arundel, Baltimore, Carroll, Cecil, Harford, Howard, Montgomery, Prince George’s, Charles, Fairfax, Alexandria, Arlington, Loudoun, Prince William, Falls Church, Manassas, Delaware, Chester, New Castle, and Stafford counties. We are continuing to grow and expand our service areas so please continue to check-in to see if we are in your area and always feel free to call if you have a question. Our service area map shows all the counties and district that we currently serve.

Master plumbers on construction jobs may be involved with developing blueprints that show the placement of all the pipes and fixtures. Their input helps ensure that a structure’s plumbing meets building codes, stays within budget, and works well with the location of other features, such as electric wires. Many diagrams are now created digitally with the use of Building Information Modeling (BIM), which allows a building’s physical systems to be planned and coordinated across occupations.


Wooden pipes were used in London and elsewhere during the 16th and 17th centuries. The pipes were hollowed-out logs, which were tapered at the end with a small hole in which the water would pass through.[16] The multiple pipes were then sealed together with hot animal fat. They were often used in Montreal and Boston in the 1800s, and built-up wooden tubes were widely used in the USA during the 20th century. These pipes, used in place of corrugated iron or reinforced concrete pipes, were made of sections cut from short lengths of wood. Locking of adjacent rings with hardwood dowel pins produced a flexible structure. About 100,000 feet of these wooden pipes were installed during WW2 in drainage culverts, storm sewers and conduits, under highways and at army camps, naval stations, airfields and ordnance plants.
Hi Kenneth, We would be happy to get you connected with a pro for your project. You can submit a service request on our website: http://www.homeadvisor.com/, or browse reviews for local water heater pros here: http://www.homeadvisor.com/c.html. We can also have a project advisor reach out to assist you if you send your contact information to [email protected] –HASupport
Sometimes, a repair job isn’t quite enough. When this happens, we offer expert plumbing installation services from our professional plumbing contractors. We strive to offer customers high-quality water heater installation service, water heater replacement, home water filtration installation, and more. We always suggest the most cost-effective repair or installation options to make sure that our solution meets your needs and your budget.

The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.


How do you know a company cares about the quality of their work? They stand behind it - that's how. At Benjamin Franklin Plumbing, the warranties and guarantees are industry leading because of our experienced technicians and the high quality parts we use. Our technicians are friendly, clean, polite, drug-free and experienced--and our techniques are state-of-the-art, guaranteed!

Most plumbers wont mess with the septic tank. We deal mostly with components inside the house. Did you have a vent pipe in the yard (often looks like a candy cane made of PVC) before the repair but not after? If all he did was replace the line it shouldn't cause a smell inside the house. All plumbing fixtures inside the house should have properly functioning traps. Those traps would create and maintain a water seal against the sewer gases. You should have at least one vent through the roof to equalize pressures within the drainage system. This prevents positive pressures within the system (caused by fixtures discharging into the lines, ie toilet flush) from pushing gas out through the traps, and negative pressures (the waste in line will pull air behind it like your finger over the end of a straw) from sucking water out of the traps.
Todd did an amazing job, and fixed a problem that could of been devastating. Replacing a leaking water heater and also a replacing a failing, leaking main shut of valve. The possibility of major flooding was a real danger It was a 12 unit townhome which made the job even trickier, as water had to be shut off to the entire building while he fixed the valve. Todd, replaced them quickly and expertly, without a hitch. Plumbing repairs are never fun for a homeowner, but these people (especially Todd) do great work. It is definitely a weight lifted off my chest.
Two-handle faucets are most often found in the bathroom, but you see them in some kitchens. Two-handle faucets use three types of mechanisms. The first two are the same as two of the mechanisms used in a single-handle faucet: cartridge and ceramic disc. The third type is a compression (or reverse-compression) mechanism. Compression faucets are the simplest type, using rubber washers that get compressed against one another to seal the valve. They do tend to wear out faster than other faucet types, but are also least expensive to repair.

The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.
My Mom is in her eightys. I called a plumber in Aug 2012, replaced the McDonnell/Miller LWCO low water cut off 47/2 $675.. Same plumber was called Jan 8,2013 back. He trouble shoot the problem and replaced the same unit, yet I still have the problem. After the heat come on for about 15 mins/ goes off.the pipes connecting to the MM LOCO the vibrating starts, shakes, and makes a loud noise. The boiler is steam, I know it's old. Do I call the same plumber or call someone differently?
"lead hung on a string to show the vertical line," early 14c., from Old French *plombe, plomee "sounding lead," and directly from Late Latin *plumba, originally plural of Latin plumbum "lead (the metal), lead ball; pipe; pencil," a word of unknown origin, related to Greek molybdos "lead" (dialectal bolimos) and perhaps from an extinct Mediterranean language, perhaps Iberian.
If nothing inside the home was altered you should not be getting a smell. Personally I'm confused as to why the repair person would have left the original line there and ran another one through a new hole. I would have pulled the old line up, ran the new line (in PVC) and used the same hole in the septic tank instead of creating a new one. Did he seal up the hole in the tank from the old line?
Hi Kenneth, We would be happy to get you connected with a pro for your project. You can submit a service request on our website: http://www.homeadvisor.com/, or browse reviews for local water heater pros here: http://www.homeadvisor.com/c.html. We can also have a project advisor reach out to assist you if you send your contact information to [email protected] –HASupport

My parents are in their middle eightys and my mother is at home with cancer. They live in SaintAugustine Florida.My problem is their two toilets will not flush all the way down the drain. I. have been down there twice to help them but I cannot drive 1200 miles each time they have a problem.So for now I would like to know what I can translate to my father over the phone to remedy this situation. Thank you very much Ray Dupuis.

I have no problem paying for any service I receive but when Allied Reddi-Rooter came into my home and immediately tell me and them tell me it would cost me 350.00 for them to install a new Rheem water heater (his recommendation) that cost 409.00 I have a problem. If the cost is exactly how Home Advisor indicates then he’s charging 350.00an hour.  I did my homework checked with other plumbers and it. Would not take an hour to remove old and install the new water heater. Thank Goodness I did my research won’t be using their services and I will be letting others know what happen to me. Shame on you Allied
"Bacon Plumbing sent their plumber Ryan to advice me on how to fix my problem. He was very through unlike other companies I talked to.. He gave me several plans of how to repair the problem and what the cost was, and the how he would do it if it was his home. He insisted on a city inpect permit and city passed it first time If Bacon Plumbling losing him, they will lose an asset. "
Galvanized steel potable water supply and distribution pipes are commonly found with nominal pipe sizes from 3⁄8 inch (9.5 mm) to 2 inches (51 mm). It is rarely used today for new construction residential plumbing. Steel pipe has National Pipe Thread (NPT) standard tapered male threads, which connect with female tapered threads on elbows, tees, couplers, valves, and other fittings. Galvanized steel (often known simply as "galv" or "iron" in the plumbing trade) is relatively expensive, and difficult to work with due to weight and requirement of a pipe threader. It remains in common use for repair of existing "galv" systems and to satisfy building code non-combustibility requirements typically found in hotels, apartment buildings and other commercial applications. It is also extremely durable and resistant to mechanical abuse. Black lacquered steel pipe is the most widely used pipe material for fire sprinklers and natural gas.
×