When you book a plumber, whether it's to fix a broken boiler or to unclog a drain, you want to know they're skilled enough for the task at hand. Nothing is worse than sending an amateur with a wrench to look at your pipes. Odds are, there will be more damage than when they started. All plumbers on the Handy platform are vetted, verified, and background checked way before they arrive at your home, so you can be sure that they're the right person for the job.
This information is not intended as an offer to sell, or the solicitation of an offer to buy, a franchise. It is for information purposes only. Read More Currently, the following states regulate the offer and sale of franchises: California, Hawaii, Illinois, Indiana, Maryland, Michigan, Minnesota, New York, North Dakota, Oregon, Rhode Island, South Dakota, Virginia, Washington, and Wisconsin. If you are a resident of or want to locate a franchise in one of these states, we will not offer you a franchise unless and until we have complied with applicable pre-sale registration and disclosure requirements in your state. Read Less Mr. Rooter is a registered trademark of Mr. Rooter LLC Copyright © 2017 Mr. Rooter, All rights reserved. All Mr. Rooter Plumbing Franchise Locations Are Independently Owned And Operated.
We offer several financing options for new equipment, as well as our Priority Club Membership that grants members exclusive discounts, priority service, annual tune-ups, and much more. Plus, we make it our mission to give back to the community that’s continually supported us for decades. Our team members regularly donate their time, money, and efforts to numerous charitable organizations, fundraising endeavors, and worthwhile causes throughout the Northern Virginia and suburban Maryland area.
plumbers must be asked directly what they charge hourly and if that is in addition to a service charge. The two are separate and I think they have gotten away with outrageous charges because of the potential of water damaging homeowner structures. I had a plumber (not Home advisor) come and replace a part in my kitchen sink that was under warranty---the spray nozzle had been leaking...He charged me $85.00 for 15 minutes of work and I will never use Mr King again.
Hello my name is Sam and I have been in the home renovation and remodeling business as well as swimming pools for over 25 years. I grew up in a family that owned skilled trade businesses. I possess abilities in all facets of the trades including but not limited to carpentry, plumbing, electrical, and more. I also have strong knowledge of home automation for lights and appliances.
Another way to avoid a service call from your plumber is to make sure the outside faucets are turned off in the winter and make sure you disconnect the outside hoses. You need to shut the water off from the inside. Then, open the valve on the outside to let the water that’s in there drain out—you switch both of them to the opposite direction so one is always closed and one is always open. We have to fix tons of these in the spring mostly because people leave their outside hoses connected and they freeze up. The repair could cost $100-$200 or more. Another tip would be if you’re going away for any length of time, like on vacation, turn off your water. If on any of those days the temperature drops below freezing, have someone check in on your house. I’ve been called to homes where the family returned from vacation, and there was water flooding out from the front door.
I had called Ben Franklin to fix a pin hole leak in the meter horn. Booking an appointment was very easy and the crew (Sid and Brandon) showed up on time. They quickly found out that a stop valve was not working and had to be replaced as well. Sid clearly explained my options and the charges upfront. He dealt with the city for water shut off, went about the job in a quick and efficient manner. Sid was very professional and explained clearly what he was doing. He patiently answered all my questions. Brandon was very practical and frank. As they were finishing up (I had to leave the house for an hour) they spotted a leak in another valve and fixed that also. I thought it was highly ethical of them to do so. Thank you Sid and Brandon!
Although plumbers, pipefitters, and steamfitters perform three distinct and specialized roles, their duties are often similar. For example, they all install pipes and fittings that carry water, steam, air, or other liquids or gases. They determine the necessary materials for a job, connect pipes, and perform pressure tests to ensure that a pipe system is airtight and watertight. Their tools include drills, saws, welding torches, and wrenches.
The Oatey 8 oz. Handy Pack Purple Primer The Oatey 8 oz. Handy Pack Purple Primer and Solvent Cement contains code-listed primer and solvent cement needed for solvent-welding PVC pipe and fittings. Can be used with up to 4 in. Dia piping. Convenient Handy Pack for storage - just add pipe and fittings. Due to the nature of ... More + Product Details Close
If your bathroom sink is slowly draining instead of holding water, your problem is super easy to fix. You likely just need to make a quick adjustment to the assembly under the sink. Pop-up drains have an arm that reaches down the drain and connects to a little rod. That rod sticks through the drain pipe and is held in place by a metal strip with holes in it. That strip, in turn, is connected to the little lever or handle you pull on to open and close the stopper. The video above from HomeAdditionPlus has an excellent look at how to make adjustments.
For many centuries, lead was the favoured material for water pipes, because its malleability made it practical to work into the desired shape. (Such use was so common that the word "plumbing" derives from plumbum, the Latin word for lead.) This was a source of lead-related health problems in the years before the health hazards of ingesting lead were fully understood; among these were stillbirths and high rates of infant mortality. Lead water pipes were still widely used in the early 20th century, and remain in many households. In addition, lead-tin alloy solder was commonly used to join copper pipes, but modern practice uses tin-antimony alloy solder instead, in order to eliminate lead hazards.