Using corrosive chemicals to dissolve a clog is like throwing a grenade down a gopher hole. Instead, Wroblewski recommends flushing your drains weekly with a half cup of baking soda and one cup of vinegar. Let it fizz in the drain for ten minutes, then pour in four cups of boiling water. Find out about the plumbing nightmares that will make you cringe.
The Oatey 8 oz. Handy Pack Purple Primer The Oatey 8 oz. Handy Pack Purple Primer and Solvent Cement contains code-listed primer and solvent cement needed for solvent-welding PVC pipe and fittings. Can be used with up to 4 in. Dia piping. Convenient Handy Pack for storage - just add pipe and fittings. Due to the nature of ... More + Product Details Close
Hello! My name is Lorinn and I am 26 years old. I have been working in different construction trades for 8+ years now. To name a few I am a skilled in flooring, cabinets/closets, and electrical(fans, fixtures, etc). I’ve gotten as experienced as I am because I genuinely enjoy working with my hands and learning new things. I take pride in my work, and love exceeding peoples expectations.
Some allege that putting a brick in the toilet tank can save water, but doing that can keep your toilet from flushing correctly. Another plumbing tip, avoid liquid drain cleaners. Liquid drain cleaners are also bad news—they eat away at the pipes. Try a plunger or, better yet, a $30 auger. Don’t have either? Here’s how to unclog a toilet without a plunger.
Most plumbers wont mess with the septic tank. We deal mostly with components inside the house. Did you have a vent pipe in the yard (often looks like a candy cane made of PVC) before the repair but not after? If all he did was replace the line it shouldn't cause a smell inside the house. All plumbing fixtures inside the house should have properly functioning traps. Those traps would create and maintain a water seal against the sewer gases. You should have at least one vent through the roof to equalize pressures within the drainage system. This prevents positive pressures within the system (caused by fixtures discharging into the lines, ie toilet flush) from pushing gas out through the traps, and negative pressures (the waste in line will pull air behind it like your finger over the end of a straw) from sucking water out of the traps.
Instead, you will be guided every step of the way. A friendly representative will greet you at your first phone call and work with you to schedule a convenient appointment time. Our plumbers take the time to listen to your concerns, address all of your questions, and make sure you receive the type of service you expect. This leaves no room for surprises.
late 14c. (from c.1100 as a surname), "a worker in any sort of lead" (roofs, gutters, pipes), from Old French plomier "lead-smelter" (Modern French plombier) and directly from Latin plumbarius "worker in lead," noun use of adjective meaning "pertaining to lead," from plumbum "lead" (see plumb (n.)). Meaning focused 19c. on "workman who installs pipes and fittings" as lead water pipes became the principal concern of the trade. In U.S. Nixon administration (1969-74), the name of a special unit for investigation of "leaks" of government secrets.
Welcome to Atlanta Plumber Repair, offering you with plumbing services in the Atlanta area and surrounding areas as well. If you are looking for residential plumbing services along with reliable commercial plumbing services, the one company in Atlanta that will be able to assist you is the one company that can offer you all this for a great and affordable price, Atlanta Plumber Repair. All of our plumbers that are with us, are either trained and fully licensed or backed with our over 25 years of plumbing experience to get you the right type of plumbing treatment for your home that you are looking for.
Plumbers, pipefitters, and steamfitters may use many different materials and construction techniques, depending on the type of project. Residential water systems, for example, use copper, steel, and plastic pipe that one or two plumbers can install. Power plant water systems, by contrast, are made of large steel pipes that usually take a crew of pipefitters to install. Some workers install stainless steel pipes on dairy farms and in factories, mainly to prevent contamination.
Let's start with the easiest possible project: Installing a new shower head is as simple as it gets. Typically, all you have to do is unscrew the old shower head from the shower arm (the pipe coming out of the wall), clean off the threads on the shower arm and wrap a bit of Teflon tape around it, then screw on the new shower head. It's really that simple (and if you don't believe me, check out the video above from Dummies.com). Do read the installation instructions on the shower head you buy, though. Some are designed not to require Teflon tape and can actually leak if you use it.
Rick’s Plumbing has been a mainstay within New Haven and Fairfield Counties since 1992. As a premier local plumbing service, we have been around for the community to complete any type of job – big or small. We only hire skilled professional plumbers to complete each task for our customers, ensuring the highest level of service is achieved within the shortest time possible. Whether you are looking for plumbing service or heating service, we’ve got you covered.
With all the freezing weather our city has had, my dad had a problem with his water pipes and I told him to call BL plumbing service. From the first phone call he made, the company gave him the most remarkable customer service. The dispatcher promptly made an appointment for him and within a couple of hours 2 workers were at his home working on the problem and fixing his pipes! The workers were very kind, helpful and extremely courteous to my dad. Not only was the work done quickly, but also, the cost of the repair was more than fair. I am so grateful for the service that was given to my dad and I will highly recommend this company to anyone needing plumbing work.
Wooden pipes were used in London and elsewhere during the 16th and 17th centuries. The pipes were hollowed-out logs, which were tapered at the end with a small hole in which the water would pass through. The multiple pipes were then sealed together with hot animal fat. They were often used in Montreal and Boston in the 1800s, and built-up wooden tubes were widely used in the USA during the 20th century. These pipes, used in place of corrugated iron or reinforced concrete pipes, were made of sections cut from short lengths of wood. Locking of adjacent rings with hardwood dowel pins produced a flexible structure. About 100,000 feet of these wooden pipes were installed during WW2 in drainage culverts, storm sewers and conduits, under highways and at army camps, naval stations, airfields and ordnance plants.