plumbers must be asked directly what they charge hourly and if that is in addition to a service charge. The two are separate and I think they have gotten away with outrageous charges because of the potential of water damaging homeowner structures. I had a plumber (not Home advisor) come and replace a part in my kitchen sink that was under warranty---the spray nozzle had been leaking...He charged me $85.00 for 15 minutes of work and I will never use Mr King again.
Most states and localities require plumbers to be licensed. Although licensing requirements vary, most states and localities require workers to have 2 to 5 years of experience and to pass an exam that shows their knowledge of the trade and of local plumbing codes before they are permitted to work independently. In addition, most employers require plumbers to have a driver’s license.
Our sewer repair and replacement experts service Baltimore, Washington D.C., Northern Virginia, Delaware and the Philadelphia Area. The specific counties we service are: Baltimore County, Howard County, Montgomery County, Prince Georges County, Anne Arundel County, Harford County, Carroll County, Fairfax, New Castle County, Delaware County, Chester County, Stafford County, Fredericksburg County, Fairfax City, Alexandria, Arlington County, Loudon County, Prince William County, Falls Church, Manassas and Cecil County.
I had another lady who said she wanted to run to the grocery store to get some coffee to make for me and my guys while we were installing her new kitchen. She said she was just gonna run to the store and asked if we wouldn’t mind keeping an eye out for her one-year-old daughter who was sleeping at the time. We said fine, but she ended up not returning until four hours later. The kid was screaming her head off and we didn’t know what to do. We tried holding her. We didn’t know if she was hungry or what to feed her. She just kept crying.
For many centuries, lead was the favoured material for water pipes, because its malleability made it practical to work into the desired shape. (Such use was so common that the word "plumbing" derives from plumbum, the Latin word for lead.) This was a source of lead-related health problems in the years before the health hazards of ingesting lead were fully understood; among these were stillbirths and high rates of infant mortality. Lead water pipes were still widely used in the early 20th century, and remain in many households. In addition, lead-tin alloy solder was commonly used to join copper pipes, but modern practice uses tin-antimony alloy solder instead, in order to eliminate lead hazards.
Water heaters are tasked with heating the water that passes through the pipes to every shower, tub, and sink. These heaters are also supposed to heat water for the washing machine and dishwasher. These units can hold up for a long time, but may begin to cause problems over time. When the heater does not heat water properly all the time, leaks, or makes odd noises, homeowners will know that there is a problem. A water heater that begins to leak could start flooding the house at any moment. A water heater that makes odd sounds could be under pressure and about to burst. In each of these cases, it could be dangerous for the homeowner, and only a licensed Manhattan plumber can fix the problem or replace the water heater altogether.
We are members of St. Gertrude's Parish and we experienced a sewer back up in our basement. I saw BEST Plumbing listed in the bulletin and I decided to give you a try. The appointment was made between 2:00pm and 4:00pm. I received a call from our plumber at approximately 1:30pm that he was in route to our house. BEST Plumbing cleared roots out of our sewer line and operated a camera in the sewer line. They discovered a riser installed improperly, which was broken at the lateral connection. BEST Plumbing made proper repairs, placed sand and backfilled the area. Our plumber was extremely courteous, helpful, and very professional throughout the entire process. We will be BEST Plumbing's biggest fans and appreciate the service. St. Gertrude's Parish
Also, you might run into a problem where the shower arm is too short or angled too sharply for the shower head you bought. This can happen more with the wand-type shower heads and the wall gets in the way of the wand. You can solve this problem by making sure you buy a shower head that fits or installing an extension arm onto the main shower arm. You can find those the same place you buy the shower heads.
Hi Kenneth, We would be happy to get you connected with a pro for your project. You can submit a service request on our website: http://www.homeadvisor.com/, or browse reviews for local water heater pros here: http://www.homeadvisor.com/c.html. We can also have a project advisor reach out to assist you if you send your contact information to [email protected] –HASupport
toilets work off of siphon.more correctly it's the timely transfer of water from the tank to the bowl through the ports that starts the siphon and carrys the solids and water downstream,thus completing a flush.i also live in florida and due to lots of hard water everywhere can tell you that most likely the toilets are full of deposits and need to be replaced or are of poor quality.all of the toilets from home depot are trash i would suggest getting one from the factory or from a plumbing supply house.DO NOT GET A 1.28gpf...1.6gpf is still legal
Accurate Leak & Line is specialized in the complete slab leak detection of sub-slab residential or commercial water and sewer piping systems. A combination of the best re-piping and Nu Flow relining repair options is offered to residential customers throughout the state. This wide variety of trenchless or traditional solutions allows our clientele to make the best decisions for their home and their pocketbook. Quality workmanship is always provided in a timely manner on all of our residential jobs, big or small.
Drain snake. This is a simple, shorter version of the big gas-powered snake that plumbers use to clear clogs deep in your drains. But if the clog is not so deep, owning one of these can save you a good bit of money. They come in different lengths and you can buy powered versions, but a simple 25' snake with a hand-powered crank will set you back less than $25.
I have no problem paying for any service I receive but when Allied Reddi-Rooter came into my home and immediately tell me and them tell me it would cost me 350.00 for them to install a new Rheem water heater (his recommendation) that cost 409.00 I have a problem. If the cost is exactly how Home Advisor indicates then he’s charging 350.00an hour. I did my homework checked with other plumbers and it. Would not take an hour to remove old and install the new water heater. Thank Goodness I did my research won’t be using their services and I will be letting others know what happen to me. Shame on you Allied
"Bacon Plumbing sent their plumber Ryan to advice me on how to fix my problem. He was very through unlike other companies I talked to.. He gave me several plans of how to repair the problem and what the cost was, and the how he would do it if it was his home. He insisted on a city inpect permit and city passed it first time If Bacon Plumbling losing him, they will lose an asset. "
If your bathroom sink is slowly draining instead of holding water, your problem is super easy to fix. You likely just need to make a quick adjustment to the assembly under the sink. Pop-up drains have an arm that reaches down the drain and connects to a little rod. That rod sticks through the drain pipe and is held in place by a metal strip with holes in it. That strip, in turn, is connected to the little lever or handle you pull on to open and close the stopper. The video above from HomeAdditionPlus has an excellent look at how to make adjustments.
To unclog a bathtub drain the right way, you'll need to take the drain plate off. That's the little round plate that has the lever on it for opening and closing the pop-up drain stopper. It takes a little effort, but it's not too hard to remove and behind that plate, you have access to a straight drain pipe you can send the drain snake down. Check out the video above from This Old House for instructions.
The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.