Pro Plumbers

Cast iron and ductile iron pipe was long a lower-cost alternative to copper, before the advent of durable plastic materials but special non-conductive fittings must be used where transitions are to be made to other metallic pipes, except for terminal fittings, in order to avoid corrosion owing to electrochemical reactions between dissimilar metals (see galvanic cell).[17]
Two-handle faucets are most often found in the bathroom, but you see them in some kitchens. Two-handle faucets use three types of mechanisms. The first two are the same as two of the mechanisms used in a single-handle faucet: cartridge and ceramic disc. The third type is a compression (or reverse-compression) mechanism. Compression faucets are the simplest type, using rubber washers that get compressed against one another to seal the valve. They do tend to wear out faster than other faucet types, but are also least expensive to repair.
If left unfixed, a running toilet or a leaky faucet can end up costing you hundreds of dollars. Check out your water bill and how your water is running. If you find your kitchen dripping non-stop and your water bill going higher, you may have a leak! Let Parker & Sons put a stop to those leaks. Our team of expert plumbers will make sure to get the work done faster, get it right the first time, and do it efficiently.
Think that by calling for plumbing services you will have to clean up after the work is done? Not when you work with us! At Bud’s Plumbing & Repair Service, our uniformed plumbers arrive at your door with shoe covers and are conscious of the cleanliness of the work area. In fact, once the job is done, you won’t be able to tell we were even there! That’s how clean we leave your property. There is no mess for you to clean up, so you can get back to your normal routine without hassle.

The difference between pipes and tubes is simply in the way it is sized. PVC pipe for plumbing applications and galvanized steel pipe for instance, are measured in IPS (iron pipe size). Copper tube, CPVC, PeX and other tubing is measured nominally, which is basically an average diameter. These sizing schemes allow for universal adaptation of transitional fittings. For instance, 1/2" PeX tubing is the same size as 1/2" copper tubing. 1/2" PVC on the other hand is not the same size as 1/2" tubing, and therefore requires either a threaded male or female adapter to connect them. When used in agricultural irrigation, the singular form "pipe" is often used as a plural.[19]


Present-day water-supply systems use a network of high-pressure pumps, and pipes in buildings are now made of copper,[25] brass, plastic (particularly cross-linked polyethylene called PEX, which is estimated to be used in 60% of single-family homes[26]), or other nontoxic material. Due to its toxicity, most cities moved away from lead water-supply piping by the 1920s in the United States,[27] although lead pipes were approved by national plumbing codes into the 1980s,[28] and lead was used in plumbing solder for drinking water until it was banned in 1986.[27] Drain and vent lines are made of plastic, steel, cast-iron, or lead.[29][30]

Much of the plumbing work in populated areas is regulated by government or quasi-government agencies due to the direct impact on the public's health, safety, and welfare. Plumbing installation and repair work on residences and other buildings generally must be done according to plumbing and building codes to protect the inhabitants of the buildings and to ensure safe, quality construction to future buyers. If permits are required for work, plumbing contractors typically secure them from the authorities on behalf of home or building owners.[citation needed]
We are licensed and insured – We are available 24 hours a day – No extras for weekends or evening services. We offer free estimates and are available anytime, no appointment needed. Call us today for any issue you have. We will first evaluate the problem for free and explain your options. You are not obligated to use us even after evaluating your problem. What makes our company different from the other companies is that we offer free estimates and free service calls. Other plumbers will charge you a fee of $35+ just to come take a look at your problem. Not us. Give us a call today.

This information is not intended as an offer to sell, or the solicitation of an offer to buy, a franchise. It is for information purposes only. Read More Currently, the following states regulate the offer and sale of franchises: California, Hawaii, Illinois, Indiana, Maryland, Michigan, Minnesota, New York, North Dakota, Oregon, Rhode Island, South Dakota, Virginia, Washington, and Wisconsin. If you are a resident of or want to locate a franchise in one of these states, we will not offer you a franchise unless and until we have complied with applicable pre-sale registration and disclosure requirements in your state. Read Less Mr. Rooter is a registered trademark of Mr. Rooter LLC Copyright © 2017 Mr. Rooter, All rights reserved. All Mr. Rooter Plumbing Franchise Locations Are Independently Owned And Operated.
Another way to avoid a service call from your plumber is to make sure the outside faucets are turned off in the winter and make sure you disconnect the outside hoses. You need to shut the water off from the inside. Then, open the valve on the outside to let the water that’s in there drain out—you switch both of them to the opposite direction so one is always closed and one is always open. We have to fix tons of these in the spring mostly because people leave their outside hoses connected and they freeze up. The repair could cost $100-$200 or more. Another tip would be if you’re going away for any length of time, like on vacation, turn off your water. If on any of those days the temperature drops below freezing, have someone check in on your house. I’ve been called to homes where the family returned from vacation, and there was water flooding out from the front door.
Occupational employment projections are developed for all states by Labor Market Information (LMI) or individual state Employment Projections offices. All state projections data are available at www.projectionscentral.com. Information on this site allows projected employment growth for an occupation to be compared among states or to be compared within one state. In addition, states may produce projections for areas; there are links to each state’s websites where these data may be retrieved.
To unclog a bathtub drain the right way, you'll need to take the drain plate off. That's the little round plate that has the lever on it for opening and closing the pop-up drain stopper. It takes a little effort, but it's not too hard to remove and behind that plate, you have access to a straight drain pipe you can send the drain snake down. Check out the video above from This Old House for instructions.
Bacteria have been shown to live in "premises plumbing systems". The latter refers to the "pipes and fixtures within a building that transport water to taps after it is delivered by the utility".[34] Community water systems have been known for centuries to spread waterborne diseases like typhoid and cholera, however "opportunistic premises plumbing pathogens" have been recognized only more recently; Legionella pneumophila discovered in 1976, Mycobacterium avium, and Pseudomonas aeruginosa are the most commonly tracked bacteria, which people with depressed immunity can inhale or ingest and may become infected with.[35] These opportunistic pathogens can grow for example in faucets, shower heads, water heaters and along pipe walls. Reasons that favor their growth are "high surface-to-volume ratio, intermittent stagnation, low disinfectant residual, and warming cycles". A high surface-to-volume ratio, i.e. a relatively large surface area allows the bacteria to form a biofilm, which protects them from disinfection.[35]
The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.
×