Pro Plumbers

 CON'T FROM COMMENTS EARLIER.  However,  the  installation took less than 3/4/ hour and was a basic regulator with no other function.  Looking up the price afterwards, invoice did not list type or price, it appears that it would have cost me around $60 for the regulator and another $15 or so for the additional supplies necessary to install it and it was really a rather simple job with easy access.    Given that, it seems that $300 for less that  an hours worth of on site work,  company says it does not include commute time in its prices, is a little high.  While flat rate quotes are nice, they must take into consideration situations where the work load differs depending on the circumstances.  Therefore, unless you are at the upper end of the harder work needed than the average job. it can be argued that my estimated price of $300 for labor was more than a little high.  Maybe I am wrong since I have not used their services for years and  am not knowledgeable of the costs of equipment and professional labor today.  
For details about apprenticeship or other opportunities in this occupation, contact the offices of the state employment service; the state apprenticeship agency; local plumbing, heating, and cooling contractors or firms that employ fitters; or local union–management apprenticeship committees. Apprenticeship information is available from the U.S. Department of Labor's Apprenticeship program online, or by phone at 877-872-5627.
Hi Kenneth, We would be happy to get you connected with a pro for your project. You can submit a service request on our website: http://www.homeadvisor.com/, or browse reviews for local water heater pros here: http://www.homeadvisor.com/c.html. We can also have a project advisor reach out to assist you if you send your contact information to [email protected] –HASupport
If nothing inside the home was altered you should not be getting a smell. Personally I'm confused as to why the repair person would have left the original line there and ran another one through a new hole. I would have pulled the old line up, ran the new line (in PVC) and used the same hole in the septic tank instead of creating a new one. Did he seal up the hole in the tank from the old line?
Welcome to Atlanta Plumber Repair, offering you with plumbing services in the Atlanta area and surrounding areas as well. If you are looking for residential plumbing services along with reliable commercial plumbing services, the one company in Atlanta that will be able to assist you is the one company that can offer you all this for a great and affordable price, Atlanta Plumber Repair. All of our plumbers that are with us, are either trained and fully licensed or backed with our over 25 years of plumbing experience to get you the right type of plumbing treatment for your home that you are looking for.
Hello! My name is Lorinn and I am 26 years old. I have been working in different construction trades for 8+ years now. To name a few I am a skilled in flooring, cabinets/closets, and electrical(fans, fixtures, etc). I’ve gotten as experienced as I am because I genuinely enjoy working with my hands and learning new things. I take pride in my work, and love exceeding peoples expectations.
Pipefitters, sometimes simply called fitters, install and maintain pipes that carry chemicals, acids, and gases. These pipes are used mostly in manufacturing, commercial, and industrial settings. Fitters install and repair pipe systems in power plants, as well as heating and cooling systems in large office buildings. Some pipefitters specialize as gasfitters, sprinklerfitters, or steamfitters.

Most plumbers wont mess with the septic tank. We deal mostly with components inside the house. Did you have a vent pipe in the yard (often looks like a candy cane made of PVC) before the repair but not after? If all he did was replace the line it shouldn't cause a smell inside the house. All plumbing fixtures inside the house should have properly functioning traps. Those traps would create and maintain a water seal against the sewer gases. You should have at least one vent through the roof to equalize pressures within the drainage system. This prevents positive pressures within the system (caused by fixtures discharging into the lines, ie toilet flush) from pushing gas out through the traps, and negative pressures (the waste in line will pull air behind it like your finger over the end of a straw) from sucking water out of the traps.

Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.
Whether it’s a leaky faucet, a broken water heater, or a troublesome sewer line, we have the experience, tools, and techniques to return your home to working order efficiently and cost-effectively. We can replace water heaters with more cost-efficient models and find and fix slab leaks. Our video camera inspection technology allows us to thoroughly explore all your plumbing and catch problems without causing damage or disruption to your home.

The projects we've laid out here are particularly simple, but plumbing can be tricky, so if you're ever unsure, don't be afraid to ask for help. These projects are all pretty straightforward, but you never know what will come up, especially with older homes. We've selected some pretty good videos, but do some research and find some other videos if something about your setup looks a little different. The Internet is a wonderful thing.
Some of the areas that we focus on include offers services in home plumbing needs where if you will be able to repair and remodel your home in Atlanta or suburban Atlanta, we offer you service in all these areas. From sink and faucet repair and replacement, depending on if you are looking for a new look or if you are looking to fix an existing a problem where your sink and faucet is leaking, we can help. We also specialize in toilet repair and replacement, as water-efficient toilets are beneficial to everyone and the environment.
If left unfixed, a running toilet or a leaky faucet can end up costing you hundreds of dollars. Check out your water bill and how your water is running. If you find your kitchen dripping non-stop and your water bill going higher, you may have a leak! Let Parker & Sons put a stop to those leaks. Our team of expert plumbers will make sure to get the work done faster, get it right the first time, and do it efficiently.
The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.
×