Whether it’s a leaky faucet, a broken water heater, or a troublesome sewer line, we have the experience, tools, and techniques to return your home to working order efficiently and cost-effectively. We can replace water heaters with more cost-efficient models and find and fix slab leaks. Our video camera inspection technology allows us to thoroughly explore all your plumbing and catch problems without causing damage or disruption to your home.
Plumbing fixtures are exchangeable devices using water that can be connected to a building's plumbing system. They are considered to be "fixtures", in that they are semi-permanent parts of buildings, not usually owned or maintained separately. Plumbing fixtures are seen by and designed for the end-users. Some examples of fixtures include water closets (also known as toilets), urinals, bidets, showers, bathtubs, utility and kitchen sinks, drinking fountains, ice makers, humidifiers, air washers, fountains, and eye wash stations.
Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.
Hello I had a plumber do an estimate for me to replace our copper pipes with plastic as we have no existing walls up in our basement yet...pretty basic job... so we figured we could upgrade as we do live in Northern Ontario and it does tend to get quite cold here in the winters. We dont have any existing problems with our plumbing right now just figured it would be good time to do the job and perhaps change the pipes to 3 quarter inch for faster flow. Well I never thought in all my life I would get an estimate back that would state $350.00 an hour in labor...yes that is correct $350.00 an hour...estimated 10 hours for the job to be completed. So he quoted me $3500.00 for labor alone.. not supplies? Well needless to say I will be happy with my half inch copper pipes and will happily wait for my bathtub to fill up at a slower pace. Just wanted to know what your thoughts are on this $350.00 an hour quote? Thank you and enjoy your day.
Accurate Leak & Line is specialized in the complete slab leak detection of sub-slab residential or commercial water and sewer piping systems. A combination of the best re-piping and Nu Flow relining repair options is offered to residential customers throughout the state. This wide variety of trenchless or traditional solutions allows our clientele to make the best decisions for their home and their pocketbook. Quality workmanship is always provided in a timely manner on all of our residential jobs, big or small.
O'Harra's Plumbing provides clients with an experienced plumbing contractor with the proper tools, parts, and knowledge to diagnose your plumbing issues. We will give you expert and honest advice on how to completely satisfy your plumbing needs. We can provide options for some of our plumbing services to best fit your budget. We give our clients an upfront estimate before work is started, so there are no surprises! We are licensed, bonded and insured. We are clean, courteous and respectful of you and your home or business.
If you need your leaky faucet repaired, don’t wait! Fill out the “Schedule Appointment” form or pick up the phone and call us today – we’ll have your leaky faucets fixed up in no time. Our plumbing technicians service Baltimore, Washington D.C., Northern Virginia, Delaware and the Philadelphia Area. The counties we service include the following: Baltimore County, Delaware County, New Castle County, Chester County, Stafford County, Fredericksburg County, Howard County, Montgomery County, Prince Georges County, Anne Arundel County, Harford County, Carroll County, Cecil County, Fairfax, Fairfax City, Alexandria, Arlington County, Loudon County, Prince William County, Falls Church and Manassas.
Stopping toilets from clogging is a function of keeping the toilet clear as well as keeping the pipes in the home clear. When the toilet is clogging often, it is best to make sure that the toilet is not being asked to flush a large number of solid products. Typically, the toilet should only be flushed with fluids. If the toilet is being overworked, it will clog. Also, the pipes in the house could begin to clog and force the toilet to clog at times when it appears that it should flush. It is best to contact annual professional cleaning services in order to keep your drains running smoothly.
Water heaters are tasked with heating the water that passes through the pipes to every shower, tub, and sink. These heaters are also supposed to heat water for the washing machine and dishwasher. These units can hold up for a long time, but may begin to cause problems over time. When the heater does not heat water properly all the time, leaks, or makes odd noises, homeowners will know that there is a problem. A water heater that begins to leak could start flooding the house at any moment. A water heater that makes odd sounds could be under pressure and about to burst. In each of these cases, it could be dangerous for the homeowner, and only a licensed Manhattan plumber can fix the problem or replace the water heater altogether.
Present-day water-supply systems use a network of high-pressure pumps, and pipes in buildings are now made of copper, brass, plastic (particularly cross-linked polyethylene called PEX, which is estimated to be used in 60% of single-family homes), or other nontoxic material. Due to its toxicity, most cities moved away from lead water-supply piping by the 1920s in the United States, although lead pipes were approved by national plumbing codes into the 1980s, and lead was used in plumbing solder for drinking water until it was banned in 1986. Drain and vent lines are made of plastic, steel, cast-iron, or lead.
Don’t flush floss, tampons, or even so-called “flushable” wipes. They don’t break down like toilet paper does and can come back to haunt you later. “Toilets are more water-efficient now than they were 20 years ago, so there sometimes isn’t enough volume in the flush to force debris down,” says Marcin Wroblewski, president of ExpressRooter Plumbing in Toronto. “An object will get lodged in the trap and cause blockage when waste builds up days later.”
Another way to avoid a service call from your plumber is to make sure the outside faucets are turned off in the winter and make sure you disconnect the outside hoses. You need to shut the water off from the inside. Then, open the valve on the outside to let the water that’s in there drain out—you switch both of them to the opposite direction so one is always closed and one is always open. We have to fix tons of these in the spring mostly because people leave their outside hoses connected and they freeze up. The repair could cost $100-$200 or more. Another tip would be if you’re going away for any length of time, like on vacation, turn off your water. If on any of those days the temperature drops below freezing, have someone check in on your house. I’ve been called to homes where the family returned from vacation, and there was water flooding out from the front door.
It’s impossible to maintain your desired levels of comfort at home or work without the proper plumbing equipment. From hot showers and reliable kitchen appliances to properly flowing sewer lines and leak-free properties, the right plumbing system can keep you from dealing with a heap of plumbing headaches. Leave it to the plumbing professionals to ensure your equipment operates year-round.
Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.
For many centuries, lead was the favoured material for water pipes, because its malleability made it practical to work into the desired shape. (Such use was so common that the word "plumbing" derives from plumbum, the Latin word for lead.) This was a source of lead-related health problems in the years before the health hazards of ingesting lead were fully understood; among these were stillbirths and high rates of infant mortality. Lead water pipes were still widely used in the early 20th century, and remain in many households. In addition, lead-tin alloy solder was commonly used to join copper pipes, but modern practice uses tin-antimony alloy solder instead, in order to eliminate lead hazards.