Pro Plumbers

Hello my name is Sam and I have been in the home renovation and remodeling business as well as swimming pools for over 25 years. I grew up in a family that owned skilled trade businesses. I possess abilities in all facets of the trades including but not limited to carpentry, plumbing, electrical, and more. I also have strong knowledge of home automation for lights and appliances.
Rick’s Plumbing has been a mainstay within New Haven and Fairfield Counties since 1992. As a premier local plumbing service, we have been around for the community to complete any type of job – big or small. We only hire skilled professional plumbers to complete each task for our customers, ensuring the highest level of service is achieved within the shortest time possible. Whether you are looking for plumbing service or heating service, we’ve got you covered.
The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.
If your bathroom sink is slowly draining instead of holding water, your problem is super easy to fix. You likely just need to make a quick adjustment to the assembly under the sink. Pop-up drains have an arm that reaches down the drain and connects to a little rod. That rod sticks through the drain pipe and is held in place by a metal strip with holes in it. That strip, in turn, is connected to the little lever or handle you pull on to open and close the stopper. The video above from HomeAdditionPlus has an excellent look at how to make adjustments.
I had 207 Plumbing come to fix a leak in my ceiling.  It's a terrible, terrible company to do business with.  He came and fixed a broken pipe in the ceiling, and I asked him to check the rest of the pipe to make sure that nothing else was broken, he said everything was OK and charged me $219.00 for 45 minutes and left.  Never cleaned up his mess.  I went to clean up the mess after he left and found there was more damage to the pipe.  I called him to come back, which he did.  He looked at the water coming down from the ceiling, into a light fixture and said he had another job to go to and couldn't come back until next week.  He also wanted to charge me $350.00 to come back.  I told him that was too much and he said he would make an exception and only charge me $219.00.  Now I have major damage done to the ceiling, the light fixture and the floor.  All of this could have been prevented if he had stayed and fixed the problem.  I will NOT hire him again.
Sometimes a faucet leak can be stopped by replacing the rubber washer at the end of a faucet stem or cartridge.  This is a more common repair on older fixtures when things were built to last and designed to be able to be maintained.  Other times the whole stem or cartridge needs replacement or the bibb seat deeper back into the fixture needs replacement.  That leads to matching up the right components and often times making a trip to the hardware store or plumbing supply house necessary due to the many varieties, makes and models of faucets.  My advice is to make sure your Plumber has faucet repair kit on their truck before having them come out to assess the issue.
Galvanized steel potable water supply and distribution pipes are commonly found with nominal pipe sizes from 3⁄8 inch (9.5 mm) to 2 inches (51 mm). It is rarely used today for new construction residential plumbing. Steel pipe has National Pipe Thread (NPT) standard tapered male threads, which connect with female tapered threads on elbows, tees, couplers, valves, and other fittings. Galvanized steel (often known simply as "galv" or "iron" in the plumbing trade) is relatively expensive, and difficult to work with due to weight and requirement of a pipe threader. It remains in common use for repair of existing "galv" systems and to satisfy building code non-combustibility requirements typically found in hotels, apartment buildings and other commercial applications. It is also extremely durable and resistant to mechanical abuse. Black lacquered steel pipe is the most widely used pipe material for fire sprinklers and natural gas.
Water systems of ancient times relied on gravity for the supply of water, using pipes or channels usually made of clay, lead, bamboo, wood, or stone. Hollowed wooden logs wrapped in steel banding were used for plumbing pipes, particularly water mains. Logs were used for water distribution in England close to 500 years ago. US cities began using hollowed logs in the late 1700s through the 1800s. Today, most plumbing supply pipe is made out of steel, copper, and plastic; most waste (also known as "soil")[21] out of steel, copper, plastic, and cast iron.[21]

If your bathroom sink is slowly draining instead of holding water, your problem is super easy to fix. You likely just need to make a quick adjustment to the assembly under the sink. Pop-up drains have an arm that reaches down the drain and connects to a little rod. That rod sticks through the drain pipe and is held in place by a metal strip with holes in it. That strip, in turn, is connected to the little lever or handle you pull on to open and close the stopper. The video above from HomeAdditionPlus has an excellent look at how to make adjustments.
I needed to hire a painter for my place of business which is a hair salon. I hired Jose and he was just fantastic! His communication was very thorough and he was on time and he did a wonderful job. I actually needed him to repaint the room from a prior painter who did a very sloppy job. Jose made my room look bright and beautiful and on top of it he cleaned everything so thoroughly. He wanted to leave my room spotless and I could tell he took a lot of pride in his services. I was very impressed with his work and I have already hired him to do a plumbing job next in my salon. He is the nicest guy you want to work with and he has an excellent work ethic. He is very upfront and honest he will tell you what he can or cannot do and his prices are very fair. Jose is going to be my go to guy for any handyman work I need in my salon going forward. I highly recommend him for whatever your handyman needs maybe. This man is a true professional!
“Don’t go to the Yellow Pages to find a plumber,” says Berkey’s Bill Stevens. “It’s like guessing lottery numbers. Anyone can make an appealing ad, but that doesn’t mean they are legitimate. In this industry, it’s easy for a plumber who develops a poor reputation to advertise under a different name. They come and go.” Even searching for someone online may end up being a scam using fake reviews. Instead, look for a plumber who is well-established in your community. Check the Better Business Bureau and read customer reviews at sites such as HomeAdvisor, Angie’s List, or Citysearch. Local contractors or plumbing fixture stores can also refer you to a quality plumber, according to Grady Daniel, who owns a plumbing company in Austin, Texas. “Most of these firms won’t work with bad plumbers.” Or simply ask your neighbors for a referral. A trusted plumber that consistently delivers quality service does not remain a secret for very long.

Most plumbers wont mess with the septic tank. We deal mostly with components inside the house. Did you have a vent pipe in the yard (often looks like a candy cane made of PVC) before the repair but not after? If all he did was replace the line it shouldn't cause a smell inside the house. All plumbing fixtures inside the house should have properly functioning traps. Those traps would create and maintain a water seal against the sewer gases. You should have at least one vent through the roof to equalize pressures within the drainage system. This prevents positive pressures within the system (caused by fixtures discharging into the lines, ie toilet flush) from pushing gas out through the traps, and negative pressures (the waste in line will pull air behind it like your finger over the end of a straw) from sucking water out of the traps.
I had called Ben Franklin to fix a pin hole leak in the meter horn. Booking an appointment was very easy and the crew (Sid and Brandon) showed up on time. They quickly found out that a stop valve was not working and had to be replaced as well. Sid clearly explained my options and the charges upfront. He dealt with the city for water shut off, went about the job in a quick and efficient manner. Sid was very professional and explained clearly what he was doing. He patiently answered all my questions. Brandon was very practical and frank. As they were finishing up (I had to leave the house for an hour) they spotted a leak in another valve and fixed that also. I thought it was highly ethical of them to do so. Thank you Sid and Brandon!
When you need plumbing or HVAC services in Castle Rock, there’s only one choice to make: PRO Plumbing Service. With more than 2500 service calls per year, we are your trusted plumbing, heating, and air conditioning company. If you are looking for a family-owned and operated plumbing and HVAC company, our top-rated HVAC contractors and plumbers ready to assist.

How do you know a company cares about the quality of their work? They stand behind it - that's how. At Benjamin Franklin Plumbing, the warranties and guarantees are industry leading because of our experienced technicians and the high quality parts we use. Our technicians are friendly, clean, polite, drug-free and experienced--and our techniques are state-of-the-art, guaranteed!
Instead, you will be guided every step of the way. A friendly representative will greet you at your first phone call and work with you to schedule a convenient appointment time. Our plumbers take the time to listen to your concerns, address all of your questions, and make sure you receive the type of service you expect. This leaves no room for surprises.
The video above from Lowe's shows how to fix leaks in all three types of single-handle faucets. Basically, you're going to remove the handle, pop out the mechanism, and replace it or the surrounding seals. If you can spot which part is causing trouble, you can buy each of the pieces individually. Otherwise, you can buy a faucet repair kit for that type of faucet and replace everything at once. Neither option should be very expensive.
No plumber is going to come right out and explain that they don’t have the required license to work for you. So if you know someone who is a great plumber, but they don’t have a license, hire them at your own risk. Licensed plumbers know the local building codes and regulations, have completed a certain amount of hours on the job and are insured. Want to become a master plumber yourself? Here are 28 tips.

Toilets – Sometimes toilet drains are overwhelmed with toilet paper or clogged by non-flushable items that find their way into the drain. Roto-Rooter can clear any toilet drain to restore full drainage and powerful flushes. Our skilled plumbers can also fix problems related to running toilets, leaking toilets, broken tanks and bowls, and toilets that don’t flush properly.
With experience and expertise, your plumber will be able to inspect your plumbing fixtures and identify where any problems may have originated. With the right tools on hand, they’ll be able to fix the problem, right there and then. If your water heater has  triggered a full-blown flood, they’ll know exactly how and where to shut off the water supply. Should the flood be the result of a burst pipe, they’ll be able to change it before it can do any additional damage. Plumbers know a lot about their craft that we do not, and the Handy platform gives you the opportunity to book them and benefit from their knowledge and ability.
 CON'T FROM COMMENTS EARLIER.  However,  the  installation took less than 3/4/ hour and was a basic regulator with no other function.  Looking up the price afterwards, invoice did not list type or price, it appears that it would have cost me around $60 for the regulator and another $15 or so for the additional supplies necessary to install it and it was really a rather simple job with easy access.    Given that, it seems that $300 for less that  an hours worth of on site work,  company says it does not include commute time in its prices, is a little high.  While flat rate quotes are nice, they must take into consideration situations where the work load differs depending on the circumstances.  Therefore, unless you are at the upper end of the harder work needed than the average job. it can be argued that my estimated price of $300 for labor was more than a little high.  Maybe I am wrong since I have not used their services for years and  am not knowledgeable of the costs of equipment and professional labor today.  
Bacteria have been shown to live in "premises plumbing systems". The latter refers to the "pipes and fixtures within a building that transport water to taps after it is delivered by the utility".[34] Community water systems have been known for centuries to spread waterborne diseases like typhoid and cholera, however "opportunistic premises plumbing pathogens" have been recognized only more recently; Legionella pneumophila discovered in 1976, Mycobacterium avium, and Pseudomonas aeruginosa are the most commonly tracked bacteria, which people with depressed immunity can inhale or ingest and may become infected with.[35] These opportunistic pathogens can grow for example in faucets, shower heads, water heaters and along pipe walls. Reasons that favor their growth are "high surface-to-volume ratio, intermittent stagnation, low disinfectant residual, and warming cycles". A high surface-to-volume ratio, i.e. a relatively large surface area allows the bacteria to form a biofilm, which protects them from disinfection.[35]
For commercial plumbing services, we provide you with ejector pump service, sump pump services and major water line repair and copper line replacement. These are just some of the services that we offer you. If you are looking for an emergency plumbing service, we can definitely assist you as well with this. Contact us today and speak with one of our reps to see how we can help you transform your remodeling at your home to something that you will be happy with. Also providing you with excellent services and excellent competitive pricing for all your plumbing needs in Atlanta and the surrounding areas.
The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.
×