Clogged drains are no fun. We've shown you several ways to clear a clogged drain and how to clear a blocked P-trap under a sink, but bathtub drains can be a little more challenging. A lot more hair and other gunk goes down them than you think. Add to this the fact that most bathtub drains take a 90-degree turn that makes getting a drain snake down them more difficult.
Don’t try to repair, replace, or install faulty or broken plumbing equipment on your own. Hire the top plumbers in town to take care of your needs! We’re capable of detecting the source of the issues fast. Trust us to advise you on the most effective solutions custom-tailored to eliminating them. Our Cincinnati plumbing company always comes prepared with the best tools and equipment. We also provide upfront pricing and money-saving deals and specials to keep more money in your pockets.
I thought that my sump pump had ended its life and needed to be replaced. The contractor I found through Home Adviser came out the following day and arrived reasonably promptly. The technician tested the pump and it wasn't responding. He then checked the breaker panel and all seemed well. However he checked to see if power was reaching the outlet, it wasn't so he tripped some breakers and reset them and the power to my pump came on and the pump works so a replacement wasn't necessary. He charged $75.00 which I think was reasonable for a call-out fee and time spent.
Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.
If your bathroom sink is slowly draining instead of holding water, your problem is super easy to fix. You likely just need to make a quick adjustment to the assembly under the sink. Pop-up drains have an arm that reaches down the drain and connects to a little rod. That rod sticks through the drain pipe and is held in place by a metal strip with holes in it. That strip, in turn, is connected to the little lever or handle you pull on to open and close the stopper. The video above from HomeAdditionPlus has an excellent look at how to make adjustments.
Welcome to Atlanta Plumber Repair, offering you with plumbing services in the Atlanta area and surrounding areas as well. If you are looking for residential plumbing services along with reliable commercial plumbing services, the one company in Atlanta that will be able to assist you is the one company that can offer you all this for a great and affordable price, Atlanta Plumber Repair. All of our plumbers that are with us, are either trained and fully licensed or backed with our over 25 years of plumbing experience to get you the right type of plumbing treatment for your home that you are looking for.
Wall thickness does not affect pipe or tubing size. 1/2" L copper has the same outer diameter as 1/2" K or M copper. The same applies to pipe schedules. As a result, a slight increase in pressure losses is realized due to a decrease in flowpath as wall thickness is increased. In other words, 1 foot of 1/2" L copper has slightly less volume than 1 foot of 1/2 M copper.
I had 207 Plumbing come to fix a leak in my ceiling. It's a terrible, terrible company to do business with. He came and fixed a broken pipe in the ceiling, and I asked him to check the rest of the pipe to make sure that nothing else was broken, he said everything was OK and charged me $219.00 for 45 minutes and left. Never cleaned up his mess. I went to clean up the mess after he left and found there was more damage to the pipe. I called him to come back, which he did. He looked at the water coming down from the ceiling, into a light fixture and said he had another job to go to and couldn't come back until next week. He also wanted to charge me $350.00 to come back. I told him that was too much and he said he would make an exception and only charge me $219.00. Now I have major damage done to the ceiling, the light fixture and the floor. All of this could have been prevented if he had stayed and fixed the problem. I will NOT hire him again.
When you need honest, reliable plumbing, heating, or cooling services in Northern Virginia, suburban Maryland, or throughout the D.C. area, look no further than My Plumber Heating and Cooling! We’re proud to be the region’s number one choice for home comfort since 1982. Whether you’re dealing with a broken air conditioner, outdated heating system, backed-up drain, or burst pipe, our highly trained team is ready to help. We offer everything from emergency plumbing repairs to new heating and air conditioning system installation to indoor air quality services and more. Most of all, we stand behind everything we do with extensive warranties and our 100% customer satisfaction guarantee. At My Plumber Heating and Cooling, your comfort is our priority! We have three convenient locations in Manassas, Fairfax, and Fredericksburg so that you don't have to wait to get the help you need.
I would highly recommend Steve Huffman of Steve's plumbing service to anyone who is looking for an experienced and efficient plumber. Having a home that is fixed with old plumbing. Steve quickly answered my distress call and was very thorough in his work very neat and clean. I was very impressed with his knowledge and willingness to keep me informed of what he was doing. His price was exactly to the quote. I will continue to use Steve for all my plumbing and electrical repairs and needs. Mahalo Steve!
CON'T FROM COMMENTS EARLIER. However, the installation took less than 3/4/ hour and was a basic regulator with no other function. Looking up the price afterwards, invoice did not list type or price, it appears that it would have cost me around $60 for the regulator and another $15 or so for the additional supplies necessary to install it and it was really a rather simple job with easy access. Given that, it seems that $300 for less that an hours worth of on site work, company says it does not include commute time in its prices, is a little high. While flat rate quotes are nice, they must take into consideration situations where the work load differs depending on the circumstances. Therefore, unless you are at the upper end of the harder work needed than the average job. it can be argued that my estimated price of $300 for labor was more than a little high. Maybe I am wrong since I have not used their services for years and am not knowledgeable of the costs of equipment and professional labor today.
Having the right tools can mean the difference between a quick project and a complete mess. Fortunately, you won't need too much to handle the projects here and what you will need is pretty inexpensive (certainly less expensive than hiring a plumber). You can get everything on this list for about $100, and you won't need it all unless you're doing all the projects. Where I live, that's about the cost of hiring a plumber for an hour.
Cast iron and ductile iron pipe was long a lower-cost alternative to copper, before the advent of durable plastic materials but special non-conductive fittings must be used where transitions are to be made to other metallic pipes, except for terminal fittings, in order to avoid corrosion owing to electrochemical reactions between dissimilar metals (see galvanic cell).