Pro Plumbers

Clogged drains are no fun. We've shown you several ways to clear a clogged drain and how to clear a blocked P-trap under a sink, but bathtub drains can be a little more challenging. A lot more hair and other gunk goes down them than you think. Add to this the fact that most bathtub drains take a 90-degree turn that makes getting a drain snake down them more difficult.

Don’t try to repair, replace, or install faulty or broken plumbing equipment on your own. Hire the top plumbers in town to take care of your needs! We’re capable of detecting the source of the issues fast. Trust us to advise you on the most effective solutions custom-tailored to eliminating them. Our Cincinnati plumbing company always comes prepared with the best tools and equipment. We also provide upfront pricing and money-saving deals and specials to keep more money in your pockets.
Water systems of ancient times relied on gravity for the supply of water, using pipes or channels usually made of clay, lead, bamboo, wood, or stone. Hollowed wooden logs wrapped in steel banding were used for plumbing pipes, particularly water mains. Logs were used for water distribution in England close to 500 years ago. US cities began using hollowed logs in the late 1700s through the 1800s. Today, most plumbing supply pipe is made out of steel, copper, and plastic; most waste (also known as "soil")[21] out of steel, copper, plastic, and cast iron.[21]
Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.

While it’s their job to make sure your pipes work like a well-oiled machine, it’s not their job to rebuild the wall they had to demolish to make that happen. So, while you’re going to get that water problem fixed, you’ll want to discuss in detail what kind of “mess” they might leave behind prior to the start of the project so you can plan accordingly. Remember, there are some jobs you can do yourself. Here’s how to solder copper pipe joints!
Water heaters are tasked with heating the water that passes through the pipes to every shower, tub, and sink. These heaters are also supposed to heat water for the washing machine and dishwasher. These units can hold up for a long time, but may begin to cause problems over time. When the heater does not heat water properly all the time, leaks, or makes odd noises, homeowners will know that there is a problem. A water heater that begins to leak could start flooding the house at any moment. A water heater that makes odd sounds could be under pressure and about to burst. In each of these cases, it could be dangerous for the homeowner, and only a licensed Manhattan plumber can fix the problem or replace the water heater altogether.

We offer service on all makes and models of heating and cooling equipment. Our skilled HVAC technicians and plumbers hold the highest industry certifications and receive ongoing training. This ensures you receive dependable service with every visit. Castle Rock residents depend on us for all their plumbing, heating, and air conditioner services. As a local, full-service plumbing company and HVAC company, we are ready to help.
Hello I had a plumber do an estimate for me to replace our copper pipes with plastic as we have no existing walls up in our basement yet...pretty basic job... so we figured we could upgrade as we do live in Northern Ontario and it does tend to get quite cold here in the winters.  We dont have any existing problems with our plumbing right now just figured it would be good time to do the job and perhaps change the pipes to 3 quarter inch for faster flow.  Well I never thought in all my life I would get an estimate back that would state $350.00 an hour in labor...yes that is correct $350.00 an hour...estimated 10 hours for the job to be completed.  So he quoted me $3500.00 for labor alone.. not supplies?  Well needless to say I will be happy with my half inch copper pipes and will happily wait for my bathtub to fill up at a slower pace.  Just wanted to know what your thoughts are on this $350.00 an hour quote?  Thank you and enjoy your day.
We offer service on all makes and models of heating and cooling equipment. Our skilled HVAC technicians and plumbers hold the highest industry certifications and receive ongoing training. This ensures you receive dependable service with every visit. Castle Rock residents depend on us for all their plumbing, heating, and air conditioner services. As a local, full-service plumbing company and HVAC company, we are ready to help.
Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.[19]
For many centuries, lead was the favoured material for water pipes, because its malleability made it practical to work into the desired shape. (Such use was so common that the word "plumbing" derives from plumbum, the Latin word for lead.) This was a source of lead-related health problems in the years before the health hazards of ingesting lead were fully understood; among these were stillbirths and high rates of infant mortality. Lead water pipes were still widely used in the early 20th century, and remain in many households. In addition, lead-tin alloy solder was commonly used to join copper pipes, but modern practice uses tin-antimony alloy solder instead, in order to eliminate lead hazards.[13]
×