Pro Plumbers

I just had my pipe under the sink unclogged  and new pipes put in $600.00, then they flushed out the pipe from under the sink to the outside pipe $700.00, Total of $1.600.00, I thought that the price was high, I got the plumber from Home Advisors, not sure they had to do all they did but they said I needed the work done.  The same evening hike using the dishwasher I had a leak in one of the pipes they put in, they came back the next day to fix it. Don't know if I will use them again.. They were K&D kitchens.
We actually have our own guide on this, but the above video from Lowe's is a good basic guide too. Do make sure to read the installation instructions that come with the faucet, though. Sometimes, there are important variations. We've only included a video on kitchen sinks here because the process of installing a bathroom sink is largely the same. However, you can always check out this video from RONAinc if you want to see the process.
My parents are in their middle eightys and my mother is at home with cancer. They live in SaintAugustine Florida.My problem is their two toilets will not flush all the way down the drain. I. have been down there twice to help them but I cannot drive 1200 miles each time they have a problem.So for now I would like to know what I can translate to my father over the phone to remedy this situation. Thank you very much Ray Dupuis.
When you need plumbing or HVAC services in Castle Rock, there’s only one choice to make: PRO Plumbing Service. With more than 2500 service calls per year, we are your trusted plumbing, heating, and air conditioning company. If you are looking for a family-owned and operated plumbing and HVAC company, our top-rated HVAC contractors and plumbers ready to assist.
Most states and localities require plumbers to be licensed. Although licensing requirements vary, most states and localities require workers to have 2 to 5 years of experience and to pass an exam that shows their knowledge of the trade and of local plumbing codes before they are permitted to work independently. In addition, most employers require plumbers to have a driver’s license.
We partner with a third party ad network to either display advertising on our Web site or to manage our advertising on other sites. Our ad network partner uses cookies and Web beacons to collect non-personally identifiable information about your activities on this and other Web sites to provide you targeted advertising based upon your interests. If you wish to not have this information used for the purpose of serving you targeted ads, you may opt-out by clicking here. Please note this does not opt you out of being served advertising. You will continue to receive generic ads.

Two-handle faucets are most often found in the bathroom, but you see them in some kitchens. Two-handle faucets use three types of mechanisms. The first two are the same as two of the mechanisms used in a single-handle faucet: cartridge and ceramic disc. The third type is a compression (or reverse-compression) mechanism. Compression faucets are the simplest type, using rubber washers that get compressed against one another to seal the valve. They do tend to wear out faster than other faucet types, but are also least expensive to repair.
Hi Ginger, We're sorry you had this experience with a plumber in our network. Have you left the review for the company? We encourage homeowners to share their experiences so others have an honest idea of the company they are hiring. If you would like to speak with a rep regarding your concerns please reach out to [email protected] If you have a review you would like to submit please send it to [email protected] or visit this link: http://www.homeadvisor.com/write-a-review/. -HASupport

toilets work off of siphon.more correctly it's the timely transfer of water from the tank to the bowl through the ports that starts the siphon and carrys the solids and water downstream,thus completing a flush.i also live in florida and due to lots of hard water everywhere can tell you that most likely the toilets are full of deposits and need to be replaced or are of poor quality.all of the toilets from home depot are trash i would suggest getting one from the factory or from a plumbing supply house.DO NOT GET A 1.28gpf...1.6gpf is still legal
Plumbing fixtures are exchangeable devices using water that can be connected to a building's plumbing system. They are considered to be "fixtures", in that they are semi-permanent parts of buildings, not usually owned or maintained separately. Plumbing fixtures are seen by and designed for the end-users. Some examples of fixtures include water closets[32] (also known as toilets), urinals, bidets, showers, bathtubs, utility and kitchen sinks, drinking fountains, ice makers, humidifiers, air washers, fountains, and eye wash stations.
Hi there! My name is Berik, welcome to my profile! I have a more than 2 years of experiences as a furniture assembling and dissembling, home appliances installation, sink drain, fixture lights, outlets and switchers, tv mount, video ring doorbell installation and sound system. Please feel free to ask any questions or concerns I will gladly answer you! Cheers!! See you soon....
Water systems of ancient times relied on gravity for the supply of water, using pipes or channels usually made of clay, lead, bamboo, wood, or stone. Hollowed wooden logs wrapped in steel banding were used for plumbing pipes, particularly water mains. Logs were used for water distribution in England close to 500 years ago. US cities began using hollowed logs in the late 1700s through the 1800s. Today, most plumbing supply pipe is made out of steel, copper, and plastic; most waste (also known as "soil")[21] out of steel, copper, plastic, and cast iron.[21]
Most large cities today pipe solid wastes to sewage treatment plants in order to separate and partially purify the water, before emptying into streams or other bodies of water. For potable water use, galvanized iron piping was commonplace in the United States from the late 1800s until around 1960. After that period, copper piping took over, first soft copper with flared fittings, then with rigid copper tubing utilizing soldered fittings.
×