Pro Plumbers

Water heaters are tasked with heating the water that passes through the pipes to every shower, tub, and sink. These heaters are also supposed to heat water for the washing machine and dishwasher. These units can hold up for a long time, but may begin to cause problems over time. When the heater does not heat water properly all the time, leaks, or makes odd noises, homeowners will know that there is a problem. A water heater that begins to leak could start flooding the house at any moment. A water heater that makes odd sounds could be under pressure and about to burst. In each of these cases, it could be dangerous for the homeowner, and only a licensed Manhattan plumber can fix the problem or replace the water heater altogether.
Wall thickness does not affect pipe or tubing size.[20] 1/2" L copper has the same outer diameter as 1/2" K or M copper. The same applies to pipe schedules. As a result, a slight increase in pressure losses is realized due to a decrease in flowpath as wall thickness is increased. In other words, 1 foot of 1/2" L copper has slightly less volume than 1 foot of 1/2 M copper.[citation needed]
In addition to Trenchless Technology, Our licensed technicians and OSHA certified excavation crews specialize in traditional tunneling and sub-slab plumbing repair / replacement.  Detailed analysis and fixed cost proposals for repair are provided to customer upon completion of a hydrostatic pressure test and diagnostic slab leak testing, using a combination of cutting-edge pipelining techniques with traditional excavation to fix foundation leaks while minimizing digging and added expense.  Traditional tunnels or trenches for water line repair or sewer repair are hand dug by crews with confined space training.
The projects we've laid out here are particularly simple, but plumbing can be tricky, so if you're ever unsure, don't be afraid to ask for help. These projects are all pretty straightforward, but you never know what will come up, especially with older homes. We've selected some pretty good videos, but do some research and find some other videos if something about your setup looks a little different. The Internet is a wonderful thing.
Hello I had a plumber do an estimate for me to replace our copper pipes with plastic as we have no existing walls up in our basement yet...pretty basic job... so we figured we could upgrade as we do live in Northern Ontario and it does tend to get quite cold here in the winters.  We dont have any existing problems with our plumbing right now just figured it would be good time to do the job and perhaps change the pipes to 3 quarter inch for faster flow.  Well I never thought in all my life I would get an estimate back that would state $350.00 an hour in labor...yes that is correct $350.00 an hour...estimated 10 hours for the job to be completed.  So he quoted me $3500.00 for labor alone.. not supplies?  Well needless to say I will be happy with my half inch copper pipes and will happily wait for my bathtub to fill up at a slower pace.  Just wanted to know what your thoughts are on this $350.00 an hour quote?  Thank you and enjoy your day.

For many centuries, lead was the favoured material for water pipes, because its malleability made it practical to work into the desired shape. (Such use was so common that the word "plumbing" derives from plumbum, the Latin word for lead.) This was a source of lead-related health problems in the years before the health hazards of ingesting lead were fully understood; among these were stillbirths and high rates of infant mortality. Lead water pipes were still widely used in the early 20th century, and remain in many households. In addition, lead-tin alloy solder was commonly used to join copper pipes, but modern practice uses tin-antimony alloy solder instead, in order to eliminate lead hazards.[13]

 CON'T FROM COMMENTS EARLIER.  However,  the  installation took less than 3/4/ hour and was a basic regulator with no other function.  Looking up the price afterwards, invoice did not list type or price, it appears that it would have cost me around $60 for the regulator and another $15 or so for the additional supplies necessary to install it and it was really a rather simple job with easy access.    Given that, it seems that $300 for less that  an hours worth of on site work,  company says it does not include commute time in its prices, is a little high.  While flat rate quotes are nice, they must take into consideration situations where the work load differs depending on the circumstances.  Therefore, unless you are at the upper end of the harder work needed than the average job. it can be argued that my estimated price of $300 for labor was more than a little high.  Maybe I am wrong since I have not used their services for years and  am not knowledgeable of the costs of equipment and professional labor today.  
Another way to avoid a service call from your plumber is to make sure the outside faucets are turned off in the winter and make sure you disconnect the outside hoses. You need to shut the water off from the inside. Then, open the valve on the outside to let the water that’s in there drain out—you switch both of them to the opposite direction so one is always closed and one is always open. We have to fix tons of these in the spring mostly because people leave their outside hoses connected and they freeze up. The repair could cost $100-$200 or more. Another tip would be if you’re going away for any length of time, like on vacation, turn off your water. If on any of those days the temperature drops below freezing, have someone check in on your house. I’ve been called to homes where the family returned from vacation, and there was water flooding out from the front door.
Before starting any work, we study the issue and perform comprehensive inspections to properly diagnose the problem. Once we have pinpointed the source of the issue, we will discuss your options with you. We try to stick to repairs if possible, and avoid recommending replacements unless your system or unit is extremely outdated. By focusing on repairs instead of replacement, you save money and enjoy an improved plumbing unit for many more years to come.
We know that plumbing problems can be a real headache, which is why the team at Michael’s Plumbing Service is dedicated to not only providing efficient service but also helping you make informed decisions about essential plumbing issues. Customers who join the Michael's Club Service program receive 15% off all services, priority scheduling, no additional service charges or fees, and two annual water heater courtesy safety inspections. We invite you to learn more about us and what we do by watching a few of our videos!

toilets work off of siphon.more correctly it's the timely transfer of water from the tank to the bowl through the ports that starts the siphon and carrys the solids and water downstream,thus completing a flush.i also live in florida and due to lots of hard water everywhere can tell you that most likely the toilets are full of deposits and need to be replaced or are of poor quality.all of the toilets from home depot are trash i would suggest getting one from the factory or from a plumbing supply house.DO NOT GET A 1.28gpf...1.6gpf is still legal
The difference between pipes and tubes is simply in the way it is sized. PVC pipe for plumbing applications and galvanized steel pipe for instance, are measured in IPS (iron pipe size). Copper tube, CPVC, PeX and other tubing is measured nominally, which is basically an average diameter. These sizing schemes allow for universal adaptation of transitional fittings. For instance, 1/2" PeX tubing is the same size as 1/2" copper tubing. 1/2" PVC on the other hand is not the same size as 1/2" tubing, and therefore requires either a threaded male or female adapter to connect them. When used in agricultural irrigation, the singular form "pipe" is often used as a plural.[19]
×