Most states and localities require plumbers to be licensed. Although licensing requirements vary, most states and localities require workers to have 2 to 5 years of experience and to pass an exam that shows their knowledge of the trade and of local plumbing codes before they are permitted to work independently. In addition, most employers require plumbers to have a driver’s license.
I had 207 Plumbing come to fix a leak in my ceiling. It's a terrible, terrible company to do business with. He came and fixed a broken pipe in the ceiling, and I asked him to check the rest of the pipe to make sure that nothing else was broken, he said everything was OK and charged me $219.00 for 45 minutes and left. Never cleaned up his mess. I went to clean up the mess after he left and found there was more damage to the pipe. I called him to come back, which he did. He looked at the water coming down from the ceiling, into a light fixture and said he had another job to go to and couldn't come back until next week. He also wanted to charge me $350.00 to come back. I told him that was too much and he said he would make an exception and only charge me $219.00. Now I have major damage done to the ceiling, the light fixture and the floor. All of this could have been prevented if he had stayed and fixed the problem. I will NOT hire him again.
Alejandro is the best, most versatile plumber I have ever used. When I needed a new toilet installed in a guest bedroom, he also did a great job replacing the the damaged tile work around the base of the old toilet. When I had new countertops installed in my kitchen, he came up with a creative solution to a problem I had with the old gas line running to my stove-top. He is not expensive, a nice guy and a true professional.
Hello I had a plumber do an estimate for me to replace our copper pipes with plastic as we have no existing walls up in our basement yet...pretty basic job... so we figured we could upgrade as we do live in Northern Ontario and it does tend to get quite cold here in the winters. We dont have any existing problems with our plumbing right now just figured it would be good time to do the job and perhaps change the pipes to 3 quarter inch for faster flow. Well I never thought in all my life I would get an estimate back that would state $350.00 an hour in labor...yes that is correct $350.00 an hour...estimated 10 hours for the job to be completed. So he quoted me $3500.00 for labor alone.. not supplies? Well needless to say I will be happy with my half inch copper pipes and will happily wait for my bathtub to fill up at a slower pace. Just wanted to know what your thoughts are on this $350.00 an hour quote? Thank you and enjoy your day.
Most plumbers, pipefitters, and steamfitters learn their trade through a 4- or 5-year apprenticeship. Apprentices typically receive 2,000 hours of paid on-the-job training, as well as some classroom instruction, each year. In the classroom, apprentices learn safety, local plumbing codes and regulations, and blueprint reading. They also study mathematics, applied physics, and chemistry. Apprenticeship programs are offered by unions and businesses. Although most workers enter apprenticeships directly, some start out as helpers. The Home Builders Institute offers a pre-apprenticeship training program in plumbing and other trades.
Pipefitters, sometimes simply called fitters, install and maintain pipes that carry chemicals, acids, and gases. These pipes are used mostly in manufacturing, commercial, and industrial settings. Fitters install and repair pipe systems in power plants, as well as heating and cooling systems in large office buildings. Some pipefitters specialize as gasfitters, sprinklerfitters, or steamfitters.
If you have questions about what parts to buy for your fixtures, the folks at the hardware store will most likely have an answer for you. Come equipped with the brand and model of your fixture and, even better, some pictures. They'll point you in the right direction. And if at any point you feel like you're in over your head, call a plumber. Even if you think you have the skills to do the job, there might be codes involved and you often need a permit.
Most large cities today pipe solid wastes to sewage treatment plants in order to separate and partially purify the water, before emptying into streams or other bodies of water. For potable water use, galvanized iron piping was commonplace in the United States from the late 1800s until around 1960. After that period, copper piping took over, first soft copper with flared fittings, then with rigid copper tubing utilizing soldered fittings.