Hello! My name is Lorinn and I am 26 years old. I have been working in different construction trades for 8+ years now. To name a few I am a skilled in flooring, cabinets/closets, and electrical(fans, fixtures, etc). I’ve gotten as experienced as I am because I genuinely enjoy working with my hands and learning new things. I take pride in my work, and love exceeding peoples expectations.
Galvanized steel potable water supply and distribution pipes are commonly found with nominal pipe sizes from 3⁄8 inch (9.5 mm) to 2 inches (51 mm). It is rarely used today for new construction residential plumbing. Steel pipe has National Pipe Thread (NPT) standard tapered male threads, which connect with female tapered threads on elbows, tees, couplers, valves, and other fittings. Galvanized steel (often known simply as "galv" or "iron" in the plumbing trade) is relatively expensive, and difficult to work with due to weight and requirement of a pipe threader. It remains in common use for repair of existing "galv" systems and to satisfy building code non-combustibility requirements typically found in hotels, apartment buildings and other commercial applications. It is also extremely durable and resistant to mechanical abuse. Black lacquered steel pipe is the most widely used pipe material for fire sprinklers and natural gas.
If nothing inside the home was altered you should not be getting a smell. Personally I'm confused as to why the repair person would have left the original line there and ran another one through a new hole. I would have pulled the old line up, ran the new line (in PVC) and used the same hole in the septic tank instead of creating a new one. Did he seal up the hole in the tank from the old line?
Todd did an amazing job, and fixed a problem that could of been devastating. Replacing a leaking water heater and also a replacing a failing, leaking main shut of valve. The possibility of major flooding was a real danger It was a 12 unit townhome which made the job even trickier, as water had to be shut off to the entire building while he fixed the valve. Todd, replaced them quickly and expertly, without a hitch. Plumbing repairs are never fun for a homeowner, but these people (especially Todd) do great work. It is definitely a weight lifted off my chest.
The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.
To unclog a bathtub drain the right way, you'll need to take the drain plate off. That's the little round plate that has the lever on it for opening and closing the pop-up drain stopper. It takes a little effort, but it's not too hard to remove and behind that plate, you have access to a straight drain pipe you can send the drain snake down. Check out the video above from This Old House for instructions.
While it’s their job to make sure your pipes work like a well-oiled machine, it’s not their job to rebuild the wall they had to demolish to make that happen. So, while you’re going to get that water problem fixed, you’ll want to discuss in detail what kind of “mess” they might leave behind prior to the start of the project so you can plan accordingly. Remember, there are some jobs you can do yourself. Here’s how to solder copper pipe joints!
For many centuries, lead was the favoured material for water pipes, because its malleability made it practical to work into the desired shape. (Such use was so common that the word "plumbing" derives from plumbum, the Latin word for lead.) This was a source of lead-related health problems in the years before the health hazards of ingesting lead were fully understood; among these were stillbirths and high rates of infant mortality. Lead water pipes were still widely used in the early 20th century, and remain in many households. In addition, lead-tin alloy solder was commonly used to join copper pipes, but modern practice uses tin-antimony alloy solder instead, in order to eliminate lead hazards.