Some allege that putting a brick in the toilet tank can save water, but doing that can keep your toilet from flushing correctly. Another plumbing tip, avoid liquid drain cleaners. Liquid drain cleaners are also bad news—they eat away at the pipes. Try a plunger or, better yet, a $30 auger. Don’t have either? Here’s how to unclog a toilet without a plunger.
I used Go Green Express Home Services for a minor plastic pipe repair under my kitchen sink...The worker did a great job fixing this minor pipe plastic pipe repair( my original pipe was too short and he needed to extended the pipe and then reconnect). It took him less than 10 minutes to fix. I was first quoted $125 +tax but when the worker went to his truck and spoke to whoever he spoke to at the office, the price rose to $155.10 +tax for a total of $167.10...I thought that was a little too high. Will I use this company again, I Don't Know. It would be helpful if they would have a set price list for jobs (minor repairs, Major repairs etc...), then you as the consumer can see beforehand what the cost maybe and work from there with the company. Minor repairs, Major repairs this company should at least have a set-price list. ..The worker was great and efficient and did a good job on the repair but their prices are a bit costly. And yes, I did write this in their review.
plumbers must be asked directly what they charge hourly and if that is in addition to a service charge. The two are separate and I think they have gotten away with outrageous charges because of the potential of water damaging homeowner structures. I had a plumber (not Home advisor) come and replace a part in my kitchen sink that was under warranty---the spray nozzle had been leaking...He charged me $85.00 for 15 minutes of work and I will never use Mr King again.
We actually have our own guide on this, but the above video from Lowe's is a good basic guide too. Do make sure to read the installation instructions that come with the faucet, though. Sometimes, there are important variations. We've only included a video on kitchen sinks here because the process of installing a bathroom sink is largely the same. However, you can always check out this video from RONAinc if you want to see the process.
To unclog a bathtub drain the right way, you'll need to take the drain plate off. That's the little round plate that has the lever on it for opening and closing the pop-up drain stopper. It takes a little effort, but it's not too hard to remove and behind that plate, you have access to a straight drain pipe you can send the drain snake down. Check out the video above from This Old House for instructions.
Also, you might run into a problem where the shower arm is too short or angled too sharply for the shower head you bought. This can happen more with the wand-type shower heads and the wall gets in the way of the wand. You can solve this problem by making sure you buy a shower head that fits or installing an extension arm onto the main shower arm. You can find those the same place you buy the shower heads.
When you’re searching for a dependable Dallas plumber or Dallas plumbing company “near me” which offers licensed and trained plumbers for any plumbing repair or plumbing installation like water heaters, tankless heaters, garbage disposals, drain or sewer lines, water filtration, water softening or other plumbing needs, call 214-324-8811214-324-8811.
Len The Plumber is a full service plumbing and drain cleaning company serving the entire Baltimore, Washington D.C., Northern Virginia, Delaware and the Philadelphia Area as well as Anne Arundel, Baltimore, Carroll, Cecil, Harford, Howard, Montgomery, Prince George’s, Charles, Fairfax, Alexandria, Arlington, Loudoun, Prince William, Falls Church, Manassas, Delaware, Chester, New Castle, and Stafford counties. We are continuing to grow and expand our service areas so please continue to check-in to see if we are in your area and always feel free to call if you have a question. Our service area map shows all the counties and district that we currently serve.
Present-day water-supply systems use a network of high-pressure pumps, and pipes in buildings are now made of copper, brass, plastic (particularly cross-linked polyethylene called PEX, which is estimated to be used in 60% of single-family homes), or other nontoxic material. Due to its toxicity, most cities moved away from lead water-supply piping by the 1920s in the United States, although lead pipes were approved by national plumbing codes into the 1980s, and lead was used in plumbing solder for drinking water until it was banned in 1986. Drain and vent lines are made of plastic, steel, cast-iron, or lead.
We've talked before about home electrical projects you can handle on your own and now it's time to tackle plumbing. The projects we're covering here mostly deal with repairing things like running toilets and leaky faucets, and replacing fixtures like faucets and shower heads. These are beginner-level projects that are fairly easy to do and can save you a lot of money if you tackle them yourself.
PVC/CPVC – rigid plastic pipes similar to PVC drain pipes but with thicker walls to deal with municipal water pressure, introduced around 1970. PVC stands for polyvinyl chloride, and it has become a common replacement for metal piping. PVC should be used only for cold water, or for venting. CPVC can be used for hot and cold potable water supply. Connections are made with primers and solvent cements as required by code.