CON'T FROM COMMENTS EARLIER. However, the installation took less than 3/4/ hour and was a basic regulator with no other function. Looking up the price afterwards, invoice did not list type or price, it appears that it would have cost me around $60 for the regulator and another $15 or so for the additional supplies necessary to install it and it was really a rather simple job with easy access. Given that, it seems that $300 for less that an hours worth of on site work, company says it does not include commute time in its prices, is a little high. While flat rate quotes are nice, they must take into consideration situations where the work load differs depending on the circumstances. Therefore, unless you are at the upper end of the harder work needed than the average job. it can be argued that my estimated price of $300 for labor was more than a little high. Maybe I am wrong since I have not used their services for years and am not knowledgeable of the costs of equipment and professional labor today.
The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.
Sometimes a faucet leak can be stopped by replacing the rubber washer at the end of a faucet stem or cartridge. This is a more common repair on older fixtures when things were built to last and designed to be able to be maintained. Other times the whole stem or cartridge needs replacement or the bibb seat deeper back into the fixture needs replacement. That leads to matching up the right components and often times making a trip to the hardware store or plumbing supply house necessary due to the many varieties, makes and models of faucets. My advice is to make sure your Plumber has faucet repair kit on their truck before having them come out to assess the issue.
We offer several financing options for new equipment, as well as our Priority Club Membership that grants members exclusive discounts, priority service, annual tune-ups, and much more. Plus, we make it our mission to give back to the community that’s continually supported us for decades. Our team members regularly donate their time, money, and efforts to numerous charitable organizations, fundraising endeavors, and worthwhile causes throughout the Northern Virginia and suburban Maryland area.
For details about apprenticeship or other opportunities in this occupation, contact the offices of the state employment service; the state apprenticeship agency; local plumbing, heating, and cooling contractors or firms that employ fitters; or local union–management apprenticeship committees. Apprenticeship information is available from the U.S. Department of Labor's Apprenticeship program online, or by phone at 877-872-5627.
Wooden pipes were used in London and elsewhere during the 16th and 17th centuries. The pipes were hollowed-out logs, which were tapered at the end with a small hole in which the water would pass through. The multiple pipes were then sealed together with hot animal fat. They were often used in Montreal and Boston in the 1800s, and built-up wooden tubes were widely used in the USA during the 20th century. These pipes, used in place of corrugated iron or reinforced concrete pipes, were made of sections cut from short lengths of wood. Locking of adjacent rings with hardwood dowel pins produced a flexible structure. About 100,000 feet of these wooden pipes were installed during WW2 in drainage culverts, storm sewers and conduits, under highways and at army camps, naval stations, airfields and ordnance plants.
Todd did an amazing job, and fixed a problem that could of been devastating. Replacing a leaking water heater and also a replacing a failing, leaking main shut of valve. The possibility of major flooding was a real danger It was a 12 unit townhome which made the job even trickier, as water had to be shut off to the entire building while he fixed the valve. Todd, replaced them quickly and expertly, without a hitch. Plumbing repairs are never fun for a homeowner, but these people (especially Todd) do great work. It is definitely a weight lifted off my chest.
Plumbing is any system that conveys fluids for a wide range of applications. Plumbing uses pipes, valves, plumbing fixtures, tanks, and other apparatuses to convey fluids. Heating and cooling (HVAC), waste removal, and potable water delivery are among the most common uses for plumbing, but it is not limited to these applications. The word derives from the Latin for lead, plumbum, as the first effective pipes used in the Roman era were lead pipes.