Pro Plumbers

Plumbing is any system that conveys fluids for a wide range of applications. Plumbing uses pipes, valves, plumbing fixtures, tanks, and other apparatuses to convey fluids.[1] Heating and cooling (HVAC), waste removal, and potable water delivery are among the most common uses for plumbing, but it is not limited to these applications.[2] The word derives from the Latin for lead, plumbum, as the first effective pipes used in the Roman era were lead pipes.[3]
Cast iron and ductile iron pipe was long a lower-cost alternative to copper, before the advent of durable plastic materials but special non-conductive fittings must be used where transitions are to be made to other metallic pipes, except for terminal fittings, in order to avoid corrosion owing to electrochemical reactions between dissimilar metals (see galvanic cell).[17]
Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.

Most plumbers wont mess with the septic tank. We deal mostly with components inside the house. Did you have a vent pipe in the yard (often looks like a candy cane made of PVC) before the repair but not after? If all he did was replace the line it shouldn't cause a smell inside the house. All plumbing fixtures inside the house should have properly functioning traps. Those traps would create and maintain a water seal against the sewer gases. You should have at least one vent through the roof to equalize pressures within the drainage system. This prevents positive pressures within the system (caused by fixtures discharging into the lines, ie toilet flush) from pushing gas out through the traps, and negative pressures (the waste in line will pull air behind it like your finger over the end of a straw) from sucking water out of the traps.


PBT – flexible (usually gray or black) plastic pipe which is attached to barbed fittings and secured in place with a copper crimp ring. The primary manufacturer of PBT tubing and fittings was driven into bankruptcy by a class-action lawsuit over failures of this system.[citation needed] However, PB and PBT tubing has since returned to the market and codes, typically first for "exposed locations" such as risers.
Most states and localities require plumbers to be licensed. Although licensing requirements vary, most states and localities require workers to have 2 to 5 years of experience and to pass an exam that shows their knowledge of the trade and of local plumbing codes before they are permitted to work independently. In addition, most employers require plumbers to have a driver’s license.
Hi Ginger, We're sorry you had this experience with a plumber in our network. Have you left the review for the company? We encourage homeowners to share their experiences so others have an honest idea of the company they are hiring. If you would like to speak with a rep regarding your concerns please reach out to [email protected] If you have a review you would like to submit please send it to [email protected] or visit this link: http://www.homeadvisor.com/write-a-review/. -HASupport
Most large cities today pipe solid wastes to sewage treatment plants in order to separate and partially purify the water, before emptying into streams or other bodies of water. For potable water use, galvanized iron piping was commonplace in the United States from the late 1800s until around 1960. After that period, copper piping took over, first soft copper with flared fittings, then with rigid copper tubing utilizing soldered fittings.
×